Phase detector characteristic

A phase detector characteristic is a function of phase difference describing the output of the phase detector.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 4 min read

Names in other languages

  • EnglishPhase detector characteristic
  • 中文鉴相器特征
  • 中文鉴相器特征
  • 简体中文鉴相器特征
  • 繁體中文鑑相器特徵

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

A phase detector characteristic is a function of phase difference describing the output of the phase detector. For the analysis of Phase detector it is usually considered the models of PD in signal (time) domain and phase-frequency domain.

In this case for constructing of an adequate nonlinear mathematical model of PD in phase-frequency domain it is necessary to find the characteristic of phase detector. The inputs of PD are high-frequency signals and the output contains a low-frequency error correction signal, corresponding to a phase difference of input signals.

For the suppression of high-frequency component of the output of PD (if such component exists) a low-pass filter is applied. The characteristic of PD is the dependence of the signal at the output of PD (in the phase-frequency domain) on the difference of phases at the input of PD. This characteristic of PD depends on the realization of PD and the types of waveforms of signals.

Consideration of PD characteristic allows to apply averaging methods for high frequency oscillations and to pass from analysis and simulation of non autonomous models of phase synchronization systems in time domain to analysis and simulation of autonomous dynamical models in phase-frequency domain . g(t) = \int\limits_0^t f^1(\theta^1(\tau))f^2(\theta^2(\tau))d \tau and filter output for phase-frequency domain model G(t) = \int\limits_0^t \varphi(\theta^1(\tau) - \theta^2(\tau))d \tau are almost equal: g(t) - G(t) \approx 0 Consider a simple case of harmonic waveforms f^1(\theta)=\sin(\theta), f^2(\theta)=\cos(\theta) and integration filter. \sin(\theta^1(t))\cos(\theta^2(t)) = \frac{1}{2}\sin(\theta^1(t) + \theta^2(t)) + \frac{1}{2}\sin(\theta^1(t) - \theta^2(t)) Standard engineering assumption is that the filter removes the upper sideband \sin(\theta^1(t) + \theta^2(t)) from the input but leaves the lower sideband \sin(\theta^1(t) - \theta^2(t)) without change. Consequently, the PD characteristic in the case of sinusoidal waveforms is \varphi(\theta) = \frac{1}{2}\sin(\theta).

Consider high-frequency square-wave signals f^1(t) = \sgn(\sin(\theta^1(t))) and f^2(t) = \sgn(\cos(\theta^2(t))) . For this signals it was found that similar thing takes place. The characteristic for the case of square waveforms is \varphi(\theta) = \begin{cases} 1+\frac{2\theta}{\pi}, & \text{if }\theta \in [-\pi,0],\\ 1-\frac{2\theta}{\pi}, & \text{if }\theta \in [0,\pi].\\ \end{cases} a^p_i=\frac{1}{\pi}\int\limits_{-\pi}^{\pi} f^p(x)\sin(ix)dx, b^p_i=\frac{1}{\pi}\int\limits_{-\pi}^{\pi} f^p(x)\cos(ix)dx, c^p_i=\frac{1}{\pi}\int\limits_{-\pi}^{\pi} f^p(x)dx, p = 1,2 the Fourier coefficients of f^1(\theta) and f^2(\theta) .

Then the phase detector characteristic is \varphi(\theta) = c^1c^2 + \frac{1}{2}\sum\limits_{l=1}^{\infty}\bigg((a^1_la^2_l + b^1_lb^2_l)\cos(l\theta) + (a^1_lb^2_l - b^1_la^2_l)\sin(l\theta)\bigg). Obviously, the PD characteristic \varphi(\theta) is periodic, continuous, and bounded on \mathbb{R} . Modeling method based on this result is described in

Text derived from https://en.wikipedia.org/w/index.php?oldid=1312446502 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001312446502 · captured 2025-09-20 · not yet sealed in the ledger · verify the chain · version history

Cite this page as: encyclopegia.org, “Phase detector characteristic”, snapshot enwiki-001312446502. https://encyclopegia.org/a/phase-detector-characteristic

Sources cited in this revision

2 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.