Point-to-point construction

In electronics, point-to-point construction is a non-automated technique for constructing circuits which was widely used before the use of printed circuit boards (PCBs) and automated assembly gradually became widespread following their…

Uses your system voice; voice and rate in settings.

≈ 5 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In electronics, point-to-point construction is a non-automated technique for constructing circuits which was widely used before the use of printed circuit boards (PCBs) and automated assembly gradually became widespread following their introduction in the 1950s. Circuits using thermionic valves (vacuum tubes) were relatively large, relatively simple (the number of large, hot, expensive devices which needed replacing was minimised), and used large sockets, all of which made the PCB less obviously advantageous than with later complex semiconductor circuits.

Point-to-point construction is still widespread in power electronics, where components are bulky and serviceability is a consideration, and to construct prototype equipment with few or heavy electronic components. A common practice, especially in older point-to-point construction, is to use the leads of components such as resistors and capacitors to bridge as much of the distance between connections as possible, reducing the need to add additional wire between the components.

Before point-to-point connection, electrical assemblies used screws or wire nuts to hold wires to an insulating wooden or ceramic board. The resulting devices were prone to fail from corroded contacts, or mechanical loosening of the connections. Early premium marine radios, especially from Marconi, sometimes used welded copper in the bus-bar circuits, but this was expensive.

The crucial invention was to apply soldering to electrical assembly. In soldering, an alloy of tin and lead (and/or other metals), known as solder, is melted and adheres to other, nonmolten metals, such as copper or tinned steel. Solder makes a strong electrical and mechanical connection.

Point-to-point wiring is not suitable for automated assembly (though see wire wrap, a similar method that is) and is carried out manually, making it both more expensive and more susceptible to wiring errors than PCBs, as connections are determined by the person doing assembly rather than by an etched circuit board. For production, rather than prototyping, errors can be minimised by carefully designed operating procedures.

An intermediate form of construction uses terminal strips (sometimes called "tag boards"), eyelet boards or turret boards. Note that if components are arranged on boards with tags, eyelets or turrets at both ends and wires going to the next components, then the construction is correctly called tag, eyelet or turret construction respectively, as the components are not going from point to point.

Although cordwood construction can be wired in a similar way the density means that component placement is usually fixed by a substrate that components are inserted into.

Breadboard

Prototypes which are subject to modification are often not made on PCBs, using instead breadboard construction. Historically this could be literally a breadboard, a wooden board with components attached to it and joined up with wire.

More recently the term is applied to a board of thin insulating material with holes at standard 0.1-inch pitch; components are pushed through the holes to anchor them, and point-to-point wired on the other side of the board. A type of breadboard specifically for prototyping has this layout, but with strips of metal spring contacts beneath a grid of holes into which components are pushed to make electrical connections like any removable connector.

Some portion of the terminals in a straight line in one direction are electrically connected, commonly in groups of 5-10 with multiple groups per row, these may be interspersed with columns that span the height of the board for the more common connections (typically the power supply rails). Such breadboards, and stripboards, fall somewhere between PCBs and point-to-point; they do not require design and manufacture of a PCB, and are as easily modified as a point-to-point setup.

Stripboard

A stripboard is a board with holes in square grid pattern, commonly with a 0.1-inch pitch; all the holes in a straight line are connected by a copper strip as on a PCB. Components are pushed through from the side without strips and soldered in place.

The strips can be interrupted by scraping out a section of the copper, stripboard cutters are available for this task which are effectively a drill bit with a handle, they are used by rotating on the holes in a strip.

See also

Wire wrap

A picture of a "dead bug" style circuit patch Progressive Wiring Techniques shows an example of point-to-point construction applied to surface-mount components.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1266244418 under CC BY-SA 4.0; modifications have been made.

Words in each sectionBreadboardBreadboardBreadboard: 187 words187StripboardStripboardStripboard: 87 words87See alsoSee alsoSee also: 2 words2
Words in each section. Measured from the stored article body; sections below the minimum are not plotted.

Provenance

snapshot enwiki-001266244418 · captured 2024-12-30 · ledger · version history

Cite this page as: encyclopegia.org, “Point-to-point construction”, snapshot enwiki-001266244418. https://encyclopegia.org/a/point-to-point-construction

Sources cited in this revision

4 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.