---
title: Programmer (hardware)
slug: programmer-hardware
qid: 
snapshot: enwiki-001358895751
content_hash: 
license: CC BY-SA 4.0
source: https://en.wikipedia.org/w/index.php?oldid=1358895751
tags: [20284588, 23118434, 23603337, 24745122, 27179390, 28269686, 34836176, 41524243, 62259234, 7692542]
---

# Programmer (hardware)

> [!note] Provenance
> Snapshot `enwiki-001358895751` · content root `…`
> Derived from <https://en.wikipedia.org/w/index.php?oldid=1358895751> · Licensed CC BY-SA 4.0

socket alt=BPM 3928 Automated Programming System|thumb|The 3928, with up to seven sites, is made for programming large data devices, such as MCUs, eMMC HS400, NAND, NOR and Serial Flash devices. High-speed signals support devices up to 200 MHz and the latest eMMC HS400 modes with data transfer rates of 2.5 nanoseconds per byte. In the context of installing firmware onto a device, a programmer, device programmer, chip programmer, device burner, or PROM writer is a device that writes, a.k.a. burns, firmware to a target device's non-volatile memory. Typically, the target programmable chip is one of the following types: PROM, EPROM, EEPROM, Flash memory, eMMC, MRAM, FeRAM, NVRAM, PLD, PLA, PAL, GAL, CPLD, FPGA, microcontroller.

socket]] [[File:BPM 3928 Automated Programming System.jpg|alt=BPM 3928 Automated Programming System|thumb|The 3928, with up to seven sites, is made for programming large data devices, such as MCUs, eMMC HS400, NAND, NOR and Serial Flash devices. High-speed signals support devices up to 200&nbsp;MHz and the latest eMMC HS400 modes with data transfer rates of 2.5 nanoseconds per byte. ]] In the context of installing firmware onto a device, a programmer, device programmer, chip programmer, device burner, or PROM writer is a device that writes, a.k.a. burns, firmware to a target device's non-volatile memory. Typically, the target programmable chip is one of the following types: PROM, EPROM, EEPROM, Flash memory, eMMC, MRAM, FeRAM, NVRAM, PLD, PLA, PAL, GAL, CPLD, FPGA, microcontroller. ==Connection== Connector-based On-Board Programmer for AVR microcontroller with USB Port interface]] Generally, a programmer connects to a device in one of two ways. ===Insertion=== In some cases, the target device is inserted into a socket (usually ZIF) on the programmer. If the device is not a standard DIP packaging, a plug-in adapter board, which converts the footprint with another socket, is used. ===Cable & port=== In some cases, a programmer connects to a device via a cable to a connection port on the device. This is sometimes called on-board programming, in-circuit programming, or in-system programming. ==Transfer== Data is transferred from the programmer to the device as signals via connecting pins. Some devices have a serial interface for receiving data (including JTAG interface). Other devices communicate on parallel pins, followed by a programming pulse with a higher voltage for programming the data into the device. Usually, a programmer is controlled via a connected personal computer through a parallel port, USB port, or LAN interface. A program on the controlling computer interacts with the programmer to perform operations such as configure install parameters and program the device, ==Types== There are four general types of programmers: Automated programmers often have multiple programming sites/sockets for mass production. Sometimes used with robotic pick and place handlers with on-board sites to support high volume and complex output such as laser marking, 3D inspection, tape input/output, etc. Development programmers usually have a single programming site; used for first article development and small-series production. Pocket programmers for development and field service. Specialized programmers for certain circuit types only, such as FPGA, microcontroller, and EEPROM programmers. ==Manufacturers== For each vendor's web site, refer to "External links" section. Batronix GmbH &amp; Co. KG BPM Microsystems Conitec Datasystems Data I/O Corporation DediProg Technology Co., Ltd Elnec s.r.o Elprosys Sp. z o.o. halec Hi-Lo System Research MCUmall Electronics Inc. Phyton, Inc. Xeltek Inc. ==See also== Off-line programming In-system programming Debug port JTAG interface Common Flash Memory Interface Open NAND Flash Interface Working Group Atmel AVR#Programming interfaces PIC microcontroller#Device programmers Intel HEX – ASCII file format SREC – ASCII file format ELF – Binary file format COFF – Binary file format Hardware description language ==References== ==External links== Technical information JEDEC - Memory Configurations: JESD21-C JEDEC - Common Flash Interface (CFI) Specification, JESD68.01, September 2003. Intel - Common Flash Interface (CFI) and Command Sets IEEE Std 1532-2002 (Revision of IEEE Std 1532-2001) - IEEE Standard for In-System Configuration of Programmable Devices What is the IEEE 1532 Standard? Keysight Technologies JEDEC - STANDARD DATA TRANSFER FORMAT BETWEEN DATA PREPARATION SYSTEM AND PROGRAMMABLE LOGIC DEVICE PROGRAMMER: JESD3-C, Jun 1994 JEDEC - JC-42 Solid State Memories Manufacturers Batronix GmbH & Co. KG BPM Microsystems Conitec Datasystems Inc. Data I/O Corporation Elnec s.r.o. Elprosys Sp. z o.o. Dediprog halec Hi-Lo System Research Co. Ltd. MCUmall Electronics Inc. Minato Holdings Inc. Phyton, Inc. Xeltek Inc.
