Quad data rate SRAM

Quad data rate (QDR) SRAM is a type of static RAM computer memory that can transfer up to four words of data in each clock cycle.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Quad data rate (QDR) SRAM is a type of static RAM computer memory that can transfer up to four words of data in each clock cycle. Like double data-rate (DDR) SDRAM, QDR SRAM transfers data on both rising and falling edges of the clock signal.

The main purpose of this capability is to enable reads and writes to occur at high clock frequencies without the loss of bandwidth due to bus-turnaround cycles incurred in DDR SRAM. QDR SRAM uses two clocks, one for read data and one for write data and has separate read and write data buses (also known as Separate I/O), whereas DDR SRAM uses a single clock and has a single common data bus used for both reads and writes (also known as common I/O). This helps to eliminate problems caused by the propagation delay of the clock wiring, and allows the illusion of concurrent reads and writes (as seen on the bus, although internally the memory still has a conventional single port - operations are pipelined but sequential).

When all data I/O signals are accounted, QDR SRAM is not 2x faster than DDR SRAM but is 100% efficient when reads and writes are interleaved. In contrast, DDR SRAM is most efficient when only one request type is continually repeated, e.g. only read cycles.

When write cycles are interleaved with read cycles, one or more cycles are lost for bus turnaround to avoid data contention, which reduces bus efficiency.…

Quad data rate (QDR) SRAM is a type of static RAM computer memory that can transfer up to four words of data in each clock cycle. Like double data-rate (DDR) SDRAM, QDR SRAM transfers data on both rising and falling edges of the clock signal.

The main purpose of this capability is to enable reads and writes to occur at high clock frequencies without the loss of bandwidth due to bus-turnaround cycles incurred in DDR SRAM. QDR SRAM uses two clocks, one for read data and one for write data and has separate read and write data buses (also known as Separate I/O), whereas DDR SRAM uses a single clock and has a single common data bus used for both reads and writes (also known as common I/O). This helps to eliminate problems caused by the propagation delay of the clock wiring, and allows the illusion of concurrent reads and writes (as seen on the bus, although internally the memory still has a conventional single port - operations are pipelined but sequential).

When all data I/O signals are accounted, QDR SRAM is not 2x faster than DDR SRAM but is 100% efficient when reads and writes are interleaved. In contrast, DDR SRAM is most efficient when only one request type is continually repeated, e.g. only read cycles.

When write cycles are interleaved with read cycles, one or more cycles are lost for bus turnaround to avoid data contention, which reduces bus efficiency. Most SRAM manufacturers constructed QDR and DDR SRAM using the same physical silicon, differentiated by a post-manufacturing selection (e.g. blowing a fuse on chip).

QDR SRAM was designed for high-speed communications and networking applications, where data throughput is more important than cost, power efficiency or density. The technology was created by Micron and Cypress, later followed by IDT, then NEC, Samsung and Renesas. Quad data rate II+ memory is currently being designed by Cypress Semiconductor for radiation hardened environments.

Clock inputs

4 clock lines: Input clock: K not-K, or /K Output clock: C not-C, or /C

Control inputs

Two control lines: not-Write enable: /WPS not-Read enable: /RPS

Buses

One address bus and two data buses: Address bus Data in bus Data out bus

Clocking scheme

Addresses Read address latched on rising edge of C Write address latched on rising edge of K (in burst-of-4 mode, burst-of-2 uses rising edge of not-K) Data Write If /WPS is low A data word on Data In is latched on rising edge of K The next data word on Data In is latched on rising edge of /K Read A read is a two-cycle process If /RPS is low The first rising edge of C latches the read address, A The second rising edge of C puts the data word, from address A, on the Data Out bus The next rising edge of /C puts the next data word, from address A+1, on the Data Out bus

AN4065 QDR-II, QDR-II+, DDR-II, DDR-II+ Design Guide

Text derived from https://en.wikipedia.org/w/index.php?oldid=1362087750 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.