RDM (lighting)
≈ 7 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
Remote Device Management (RDM) is an addition to the DMX512 control protocol for stage lighting equipment, introduced in 2006. DMX512 was developed in the late 1980s as a standard protocol for lighting consoles to communicate with dimmers, but has since been used for more complex applications, including the control of intelligent lighting fixtures. The addition of RDM addresses many of the shortcomings of DMX512, which is unidirectional with no support for metadata. RDM revises the DMX512 standard to include bidirectional communication, and introduces additional options for the configuration of fixtures over the DMX512 network. RDM is backwards compatible with existing DMX512 devices, and requires few changes to the physical cabling of DMX512 networks. The RDM standard was developed by the Entertainment Services and Technology Association, and is maintained as ANSI E1.20.
Remote Device Management (RDM) is an addition to the DMX512 control protocol for stage lighting equipment, introduced in 2006. DMX512 was developed in the late 1980s as a standard protocol for lighting consoles to communicate with dimmers, but has since been used for more complex applications, including the control of intelligent lighting fixtures. The addition of RDM addresses many of the shortcomings of DMX512, which is unidirectional with no support for metadata. RDM revises the DMX512 standard to include bidirectional communication, and introduces additional options for the configuration of fixtures over the DMX512 network. RDM is backwards compatible with existing DMX512 devices, and requires few changes to the physical cabling of DMX512 networks. The RDM standard was developed by the Entertainment Services and Technology Association, and is maintained as ANSI E1.20.
Compatibility
RDM is enabled in many new lighting devices, and can be used in the same network as non-RDM-enabled devices, using existing cabling. DMX512 devices that do not support RDM should ignore all RDM commands, but in practice, some devices do malfunction when receiving RDM signals. DMX networks may include splitters with opto-isolator functionality, which only allow signal transmission in one direction, and filter out RDM signals. DMX splitters that pass through RDM signals are available, but not all splitters include this functionality. RDM is a technology specific to DMX512 signals over standard twisted-pair wire. Protocols that carry DMX signal over IP networks, such as Streaming ACN and Art-Net, have their own implementations of remote control which are backwards compatible with RDM.
Technical specifications
RDM Physical layer
The RDM protocol and the RDM physical layer were designed to be compatible with legacy equipment. All compliant legacy DMX512 receivers should be usable in mixed systems with an RDM controller (console) and RDM responders (receivers). DMX receivers and RDM responders can be used with a legacy DMX console to form a DMX512 only system. From a user’s point of view the system layout is very similar to a DMX system. The controller is placed at one end of the main cable segment. The cable is run receiver to receiver in a daisy-chain fashion. RDM enabled splitters are used the same way DMX splitters would be. The far end (the non console or splitter end) of a cable segment should be terminated. RDM requires two significant topology changes compared to DMX. However, these changes are generally internal to equipment and therefore not seen by the user. First, a controller’s (console’s) output is terminated. Second, this termination must provide a bias to keep the line in the ‘marking state’ when no driver is enabled. The reason for the additional termination is that a network segment will be driven at many points along its length. Hence, either end of the segment, if unterminated, will cause reflections. A DMX console’s output drivers are always enabled. The RDM protocol is designed so that except during discovery, there should never be data collisions. To ensure this lack of collisions, while making possible implementation on different platforms, there are times when all line drivers are required to be disabled. If nothing more than the termination was done, the line would float to some unknown level. In that case one or more random changes might be read on the line. These random changes greatly decrease system accuracy. So the biasing of the line is required To assure this, section 2.4.1 (Line Bias Networks) of the standard says; “The command port shall provide a means to bias the termination of the data link to a value of at least 245 mV and verified by using the test circuit described in Appendix F.” The standard further states that, the biasing mean “shall be polarized such that Data+ of the data link is positive with respect to Data- the data link. The Line Biasing network shall maintain this bias when the data link is loaded with the equivalent of 32 unit loads and common mode voltage is varied over the range of +7 volts to -7 volts DC.” The standard does not require any particular circuit for providing the basis and termination; however, the simplest method is often a passive pull apart network. Whatever method is used must be tested with the chosen driver chip to see that the design combination still meets the requirement of E1.20. Tests are given in Appendix F of the standard. These tests are for design verification and are not required as production testing. Experience has shown many EIA485 drivers designed for 5 volt operation will pass the required tests. It is not so clear that all 3.3 volt parts will pass. In either case this performance must be verified. Details of the pull apart network and the tests can be found in ANSI E1.20 - 2006.
Discovery
Discovery is the only situation in which data collisions can occur assuming all connected devices behave correctly. The controller will broadcast a discovery command to all devices and await a response. If there are more than one device connected, the simultaneous responses will likely result in a data collision, and the controller will not receive a correctly formatted response. The controller will then refine its search to a smaller range of UIDs according to a binary search pattern. Once the controller receives a correct response it will attempt to mute the responding device. After a successful mute, the device is no longer allowed to respond to discovery messages, and the controller can continue searching for other devices. Once all devices have been muted (no responses are received to discovery commands), the discovery process is finished and the controller will hold a list of all connected devices. The controller will need to periodically perform searches for new devices and assert that already discovered devices are still connected.
Unicast communication
General communication with a specific fixture occurs in a request-response pattern. The controller sends the request to the device, addressing it by the device's UID. When the request has been sent, the controller relinquishes control of the DMX line for a given period of time, so the device can transmit its response. Unicast communication is the only way in which data can be retrieved from a fixture (other than its UID which can be obtained using the discovery mechanism mentioned above). If the device does not respond within a given period of time, the controller can assume communication has failed, and may retry.
Broadcast communication
To quickly send instructions to multiple fixtures, RDM allows for broadcast communication. This allows the controller to send an instruction to all devices, or all devices from one manufacturer. As more than one device might be receiving the message, responses are not permitted in broadcast communication except during the Discovery process.
See also
Dimmer Lighting control console Lighting control system
External links
RDM Protocol Developer and User Forums
Text derived from https://en.wikipedia.org/w/index.php?oldid=1366628308 under CC BY-SA 4.0; modifications have been made.