Regenerative braking

tram on the London Underground can return around 20% of its energy usage to the power supply.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 10 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

tram on the London Underground can return around 20% of its energy usage to the power supply. Regenerative braking is an energy recovery mechanism that slows down a moving vehicle or object by converting its kinetic energy or potential energy into a form that can be either used immediately or stored until needed.

Typically, regenerative brakes work by driving an electric motor in reverse to recapture energy that would otherwise be lost as heat during braking, effectively turning the traction motor into an electric generator. Feeding power backwards through the system like this allows the energy harvested from deceleration to resupply an energy storage solution such as a battery or a capacitor.

Once stored, this power can then later be used again to aid propulsion. Because of the electrified vehicle architecture required for such a braking system, automotive regenerative brakes are most commonly found on hybrid and electric vehicles.

This method contrasts with conventional braking systems, where excess kinetic energy is converted to unwanted and wasted heat due to friction in the brakes. Similarly, with rheostatic brakes, energy is recovered by using electric motors as generators but is immediately dissipated as heat in resistors.

In addition to improving the overall efficiency of the vehicle, regeneration can significantly extend the life of the braking system.…

tram on the London Underground can return around 20% of its energy usage to the power supply. Regenerative braking is an energy recovery mechanism that slows down a moving vehicle or object by converting its kinetic energy or potential energy into a form that can be either used immediately or stored until needed.

Typically, regenerative brakes work by driving an electric motor in reverse to recapture energy that would otherwise be lost as heat during braking, effectively turning the traction motor into an electric generator. Feeding power backwards through the system like this allows the energy harvested from deceleration to resupply an energy storage solution such as a battery or a capacitor.

Once stored, this power can then later be used again to aid propulsion. Because of the electrified vehicle architecture required for such a braking system, automotive regenerative brakes are most commonly found on hybrid and electric vehicles.

This method contrasts with conventional braking systems, where excess kinetic energy is converted to unwanted and wasted heat due to friction in the brakes. Similarly, with rheostatic brakes, energy is recovered by using electric motors as generators but is immediately dissipated as heat in resistors.

In addition to improving the overall efficiency of the vehicle, regeneration can significantly extend the life of the braking system. This is because the traditional mechanical parts like discs, calipers, and pads – included for when regenerative braking alone is insufficient to safely stop the vehicle – will not wear out as quickly as they would in a vehicle relying solely on traditional brakes.

Practical regenerative braking

Regenerative braking is not by itself sufficient as the sole means of safely bringing a vehicle to a standstill, or slowing it as required, so it must be used in conjunction with another braking system such as friction-based braking. The regenerative braking effect drops off at lower speeds and cannot bring a vehicle to a complete halt reasonably quickly with current technology.

However, some cars, like the Chevrolet Bolt, can bring the vehicle to a complete stop on level surfaces when the driver knows the vehicle's regenerative braking distance. This is referred to as one-pedal driving (OPD). Some current regenerative brakes do not immobilize a stationary vehicle; physical locking is required, for example, to prevent vehicles from rolling down hills.

Some cars, like the Chevrolet Bolt, can remain stationary on small slopes using only the motor. Many road vehicles with regenerative braking do not have drive motors on all wheels (as in a two-wheel drive car); regenerative braking is normally only applicable to wheels with motors. For safety, the ability to brake all wheels is required.

The regenerative braking effect available is limited, and mechanical braking is still necessary for substantial speed reductions or to bring a vehicle to a stop. On steep hills with real traffic speeds, the magnitude of potential energy recoverable during the descent of a vehicle at a slower speed than its terminal speed is substantially greater than that recoverable by bringing the vehicle from even the terminal speed to a complete stop.

An example used by bicyclists is that during the descent of a hill, approximately three hair dryers' worth of power or some two horsepower is lost to air drag at terminal speeds. Regenerative and friction braking must both be used, creating the need to control them to produce the required total braking. The GM EV-1 was the first commercial car to do this.

In 1997 and 1998, engineers Abraham Farag and Loren Majersik were issued two patents for this brake-by-wire technology. Early applications commonly suffered from a serious safety hazard: in many early electric vehicles with regenerative braking, the same controller positions were used to apply power and to apply the regenerative brake, with the functions being swapped by a separate manual switch.

This led to a number of serious accidents when drivers accidentally accelerated when intending to brake, such as the runaway train accident in Wädenswil, Switzerland in 1948, which killed twenty-one people. In the 2020s, most vehicles equipped with regenerative braking can completely halt reasonably quickly in one-pedal driving mode.

Some car models do not illuminate the braking light when engaging in regenerative braking, leading to safety concerns. Most regulations do not mandate the illumination of a braking light when the vehicle decelerates through regenerative braking.

The one-pedal driving (OPD) mode also leads to concerns over sudden unintended acceleration (SUA), as the driver could confuse the accelerator as the brake in stressful situations when the latter is seldomly used during OPD operation. The GB 21670-2025 vehicle standard later mandated that brake lights must turn on during regenerative braking when deceleration exceeds 1.3 m/s 2 .

Streetcars/trams

Power consumption is reduced by regenerative braking on streetcars ( ) or trams ( ) in Oranjestad, Aruba. Designed and built by TIG/m Modern Street Railways in Chatsworth, USA, the vehicles use hybrid/electric technology: they do not take their power from external sources such as overhead wires when running but are self-powered by lithium batteries augmented by hydrogen fuel cells.

E_\text{in}-E_\text{out}= \Delta E_\text{system} where E_\text{in} is the energy into the flywheel. E_\text{out} is the energy out of the flywheel. \Delta E_\text{system} is the change in energy of the flywheel.

An assumption is made that during braking there is no change in the potential energy, enthalpy of the flywheel, pressure or volume of the flywheel, so only kinetic energy will be considered. As the car is braking, no energy is dispersed by the flywheel, and the only energy into the flywheel is the initial kinetic energy of the car.

The equation can be simplified to: \frac{mv^2} {2} = \Delta E_\text{fly} where m is the mass of the car. v is the initial velocity of the car just before braking. The flywheel collects a percentage of the initial kinetic energy of the car, and this percentage can be represented by \eta_\text{fly} . The flywheel stores the energy as rotational kinetic energy.

Because the energy is kept as kinetic energy and not transformed into another type of energy this process is efficient. The flywheel can only store so much energy, however, and this is limited by its maximum amount of rotational kinetic energy. This is determined based upon the inertia of the flywheel and its angular velocity.

As the car sits idle, little rotational kinetic energy is lost over time so the initial amount of energy in the flywheel can be assumed to equal the final amount of energy distributed by the flywheel. The amount of kinetic energy distributed by the flywheel is therefore: KE_\text{fly}=\frac{\eta_\text{fly} mv^2} {2} 𝐸re=∫ ( 𝐹bm * ⁡𝑣 / 𝜂 ) d𝑡 where 𝐹bm is braking force, 𝑣 is the vehicle speed, and 𝜂 is the energy transfer efficiency in the braking energy recovery system (BERS). which may be affected by battery state of charge (SOC) and ambient temperature.

In general, about 0.9. Regenerative braking has a similar energy equation to the equation for the mechanical flywheel. Regenerative braking is a two-step process involving the motor/generator and the battery.

The initial kinetic energy is transformed into electrical energy by the generator and is then converted into chemical energy by the battery. This process is less efficient than the flywheel. The efficiency of the generator can be represented by: \eta_\text{gen}=\frac{W_\text{out}}{W_\text{in}} where W_\text{in} is the work into the generator.

W_\text{out} is the work produced by the generator. The only work into the generator is the initial kinetic energy of the car and the only work produced by the generator is the electrical energy.

Rearranging this equation to solve for the power produced by the generator gives this equation: P_\text{gen}= \frac{\eta_\text{gen} mv^2}{2 \, \Delta t} where \Delta t is the amount of time the car brakes. m is the mass of the car. v is the initial velocity of the car just before braking. The efficiency of the battery can be described as: \eta_\text{batt}=\frac{P_\text{out}} {P_\text{in}} where P_\text{in}=P_\text{gen} P_\text{out}=\frac{W_\text{out}}{\Delta t} The work out of the battery represents the amount of energy produced by the regenerative brakes.

This can be represented by: W_\text{out}=\frac{\eta_\text{batt} \eta_\text{gen} mv^2}{2} Consider the electric motor efficiency \eta_\text{eng}=0.5 and the braking proportion in towns p=0.46 and on motorways p=0.1 . Let us introduce \eta_\text{recup} which is the recuperated proportion of braking energy. Let us assume \eta_\text{recup}=0.6 .

Under these circumstances, E being the energy flux arriving at the electric engine, E_\text{braking} the energy flux lost while braking and E_\text{recup} the recuperated energy flux, an equilibrium is reached according to the equations E_\text{braking}=(E + E_\text{recup}) \cdot \eta_\text{eng} \cdot p and E_\text{recup}=\eta_\text{recup} \cdot E_\text{braking} thus E_\text{braking}=\frac {E \cdot \eta_\text{eng} \cdot p} {1-\eta_\text{eng} \cdot p \cdot \eta_\text{recup}} It is as though the old energy flux E was replaced by a new one E \cdot (1-\eta_\text{eng} \cdot p \cdot \eta_\text{recup}) The expected gain amounts to \eta_\text{eng} \cdot p \cdot \eta_\text{recup} The higher the recuperation efficiency, the higher the recuperation. The higher the efficiency between the electric motor and the wheels, the higher the recuperation.

The higher the braking proportion, the higher the recuperation. On motorways, this figure would be 3%, and in cities it would amount to 14%.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1378718919 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

26 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.