RF chain
≈ 15 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
An RF chain is a cascade of electronic components and sub-units which may include amplifiers, filters, mixers, attenuators and detectors. It can take many forms, for example, as a wide-band receiver-detector for electronic warfare (EW) applications, as a tunable narrow-band receiver for communications purposes, as a repeater in signal distribution systems, or as an amplifier and up-converters for a transmitter-driver. In this article, the term RF (radio frequency) covers the frequency range "medium Frequencies" up to "microwave Frequencies", i.e. from 100 kHz to 20 GHz. The key electrical parameters for an RF chain are system gain, noise figure (or noise factor) and overload level. Other important parameters, related to these properties, are sensitivity (the minimum signal level which can be resolved at the output of the chain); dynamic range (the total range of signals that the chain can handle from a maximum level down to smallest level that can be reliably processed) and spurious signal levels (unwanted signals produced by devices such as mixers and non-linear amplifiers). In addition, there may be concerns regarding the immunity to incoming interference or, conversely, the amount of undesirable radiation emanating from the chain. The tolerance of a system to mechanical vibration may be important too.…
An RF chain is a cascade of electronic components and sub-units which may include amplifiers, filters, mixers, attenuators and detectors. It can take many forms, for example, as a wide-band receiver-detector for electronic warfare (EW) applications, as a tunable narrow-band receiver for communications purposes, as a repeater in signal distribution systems, or as an amplifier and up-converters for a transmitter-driver. In this article, the term RF (radio frequency) covers the frequency range "medium Frequencies" up to "microwave Frequencies", i.e. from 100 kHz to 20 GHz. The key electrical parameters for an RF chain are system gain, noise figure (or noise factor) and overload level. Other important parameters, related to these properties, are sensitivity (the minimum signal level which can be resolved at the output of the chain); dynamic range (the total range of signals that the chain can handle from a maximum level down to smallest level that can be reliably processed) and spurious signal levels (unwanted signals produced by devices such as mixers and non-linear amplifiers). In addition, there may be concerns regarding the immunity to incoming interference or, conversely, the amount of undesirable radiation emanating from the chain. The tolerance of a system to mechanical vibration may be important too. Furthermore, the physical properties of the chain, such as size, weight and power consumption may also be important considerations. An addition to considering the performance of the RF chain, the signal and signal-to-noise requirements of the various signal processing components, which may follow it, are discussed because they often determine the target figures for a chain. \mathrm{Gcum}_n = \mathrm{Gcum}_{n-1} \times G_n and Gcum n (dB) is given by \mathrm{Gcum}_n(dB) = \mathrm{Gcum}_{n - 1}(dB) + G_n(dB) where Gcum n−1 [dB] is the total gain of the first stages and G n [dB] is the gain of the nth stage. Conversion equations between logarithmic and linear terms are: G = 10^{G(dB)/10} = \exp \big (0.23026 \times G(dB) \big ) and G(dB) = 10 \times \log_{10}G = 4.6429 \times \ln(G) \mathrm{Fcum}_n = \mathrm{Fcum}_{n - 1} +\frac{F_n -1}{\mathrm{Gcum}_{n-1}} where Fcum n−1 is the noise factor of the first stages, F n is the noise factor of the nth stage, and Gcum n is the overall gain of n stages. The cumulative noise figure is then \mathrm{NFcum}_n(dB) = 10 \times \log_{10}(\mathrm{Fcum}_n) = 4.6429 \times \ln(\mathrm{Fcum}_n) Note 1: the use of an amplifier with high gain for the first stage will ensure that the noise figure degradations by later stages will be small or negligible. This will be best for system sensitivity, see later. Note 2: for a passive (lossy) section of the chain, the noise figure of the section equals the loss of that section. So, for example, a 3 dB attenuator has a noise figure of 3 dB. P1cum_n(input) = \frac{1}{ \frac{1}{P1cum_{n-1}(input)} + \frac{Gcum_n}{P1_n(input)}} where P1cum n-1 is the 1 dB compression point at the input of the first stages, P1 n is the 1 dB compression point for the nth stage, referred to its input and Gcum n is the overall gain including the nth stage. The unit is [mW] or [W]. Note: for the best result, i.e. a system tolerant to high level signals, is achieved with a low front end gain. This is in conflict with the need for a low overall noise factor, which requires a high first-stage gain. Note 2: The 1 dB compression point is abbreviated as P1dB, iP1dB, or oP1dB. It is referenced to input or output power level measured in [dBm]. Overall system performance can be practically evaluated by the 1 dB compression method. Related parameters, such as IP3 or IM3 are helpful fictive numbers used to evaluate the system. The device would burn, applying IP3 input level. Accuracy of the measurement with spectrum analyzer is (HP/Agilent specs: ±1.0 dB, and ±0.5 dB custom device). In linear systems, this all results in AGC. The thermal noise power present at the input of an RF chain, is a maximum in a resistively matched system, and is equal to kTB, where k is the Boltzmann constant (= ), T is the absolute temperature, and B is the bandwidth in Hz. At a temperature of 17 °C (≡ 290 K), kTB = 4.003 × 10 −15 W/MHz ≡ −114 dBm for 1 MHz bandwidth. The thermal noise after n stages of an RF chain, with total gain G T and noise figure F T is given by Ncum_n = kTB \times Fcum_n \times Gcum_n where k = the Boltzmann constant, T is the temperature in kelvins and B is the bandwidth in hertz, or Ncum_n(dBm/Mhz) = -114 +Fcum_n(dB) + Gcum_n(dB) where Ncum n (dBm) is the total noise power in dBm per 1 MHz of bandwidth, In receivers, the cumulative gain is set to ensure that the output noise power of the chain at an appropriate level for the signal processing stages that follow. For example, the noise level at the input to an analog-to-digital converter (ADC) must not be at too low a level, otherwise the noise (and any signals within it) is not properly characterized (see the section on ADCs, later). On the other hand, too high a level results in the loss of dynamic range. I2cum_n(input) = \frac{1}{ \frac{1}{I2cum_{n-1}(input)} + \frac{Gcum_n}{I2_n(input)}} where I2cum n−1 is the second order intercept point at the input of the first stages, I2 n is the third order intercept point for the nth stage, referred to its input and Gcum n is the overall gain including the nth stage. Similarly, I3cum_n(input) = \frac{1}{ \frac{1}{I3cum_{n-1}(input)} + \frac{Gcum_n}{I3_n(input)}} where I3cum n-1 is the third order intercept point at the input of the first stages, I3 n is the third order intercept point for the nth stage, referred to its input. The cumulative intercept points are useful when determining the "spurious free dynamic range" of a system. There is an approximate relationship between the third order intercept level and the 1 dB compression level which is IP3(dB) \approx P1(dB) + 11(dB) Although only an approximation, the relationship is found to apply to a large number of amplifiers. In the spread sheet, the total frequency band of interest B(Hz) is divided into M sub-bands (spreadsheet columns) of B/M (Hz) each, and for each sub-band (m = 1 to M) the thermal noise power is derived, as described above. In practice, these results will differ slightly, from column to column, if the system has gain ripple. The signal-to-noise ratio (S:N) is the peak signal power of the pulse (P sig ) divided by the total noise power (P noise ) from the M frequency bins, i.e. \frac{S}{N} = \frac{P_\text{sig}}{ \sum_{m=1}^M P_\text{noise}(m)} This is the S:N ratio at RF frequencies. It can be related to the video S:N ratio as shown next. \Big ( \frac {S}{N} \Big )_\text{vid} = \frac {G^2.P_S^2}{4.G^2.P_S.kTF'B_V + 2(kTF'G)^2.(B_V.B_R- B_v^2/2)} where P S = input RF signal power; 8B V and B R are the video and RF bandwidths; F′ = F − 1/G where G is the chain gain and F is the effective noise figure; k = the Boltzmann constant; and T = the ambient temperature [If there is significant gain variation across the band, then it can be divided into M sub-bands and results summed for these sub-bands, as described earlier.] From the above equation, as the noise power in the RF band is P N = kTB R F′, a relationship between RF and video S:N ratios can be found. \Big ( \frac {S}{N} \Big )_{vid} = \frac {\Big ( \frac {S}{N} \Big )_{rf}^2}{4. \Big ( \frac{S}{N} \Big)_{rf} . \frac{B_V}{B_R} +2. \frac{B_V}{B_R} - \Big ( \frac{B_V}{B_R} \Big ) ^2} (This result can be found elsewhere ). Inverting the relationship gives the RF signal-to-noise ratio required to achieve a given video S:N ratio: \Big ( \frac {S}{N} \Big )_{rf} = \frac{B_V}{B_R}. \Bigg [ 2.\Big( \frac{S}{N} \Big )_{vid} \pm \sqrt { 4. \Big (\frac{S}{N} \Big )_{vid}^2 + \Big( \frac{S}{N} \Big )_{vid} . \Big ( 2. \frac{B_R}{B_V} -1 \Big )} \Bigg ] TSS(dBm) = 114 + 10.logF_T + 10 \log \Big ( 6.31 B_V = 2.5 \sqrt {2.B_V B_R - B_V^2} \Big ) From this, the S:N of the RF signal, at the input to the detector can be obtained when the video output is at TSS. \Big (\frac{S}{N} \Big )_R(dB) =10 \log \Bigg [ \frac{B_V}{B_R} \Bigg(6.31 + 2.5 \sqrt{2 \frac{B_R}{B_V} - 1} \Bigg) \Bigg ] This equation shows that the S:N at RF is typically less than unity, in wideband systems, when the video output is at TSS. For example, if B R /B V = 500 then the equation gives (S:N) R = 0.17 (≈ −7.7 dB). (Note: a similar result is obtained by using the equation relating RF and video S:N ratios, given in the previous section ). The thumbnail shows the simulated video output (at TSS) corresponding to an RF pulse in wideband noise with S:N = 0.17 and a bandwidth ratio of 500. As examples, thumbnails show simulated examples of a detected pulse, in noise, where S:N = 18 dB and 15 dB. As can be seen, if the S:N falls to 15 dB or lower, it becomes difficult to set a threshold level for pulse detection, that is clear of the noise floor, and yet does not result in early termination. The video S:N ratio can be related to the RF S:N ratio, as shown earlier. In scenarios, such as radar pulse detection, integration over several pulses may occur and a lower value of S:N then becomes acceptable. In general, system sensitivity and pulse detection theory are specialized topics and often involve statistical procedures not easily adapted for spreadsheets. Voltage Reflection coefficient = Γ, where Γ = (Z I − Z 0 )/(Z I + Z 0 ) Return loss(power) = 20 log VSWR = (1 + Γ)/(1 − Γ) (see Standing wave ratio) Mismatch loss = −10 log(1 − Γ 2 ) V_\text{out} = V_1 ( 1 + \alpha ^2 \ \rho_1 \ \rho_2 \ e^{j \ 2 \pi f \ 2 T_\text{d}} ) where α is the loss for a single pass through the cable, ρ 1 and ρ 2 are the voltage reflection coefficients of the terminations, f is the frequency, T d is the (single pass) propagation delay of the cable A typical plot is shown in the thumbnail. This response has a ripple component with a peak-to-peak value ΔA, given by \Delta A = 2 \frac{1 + \rho_1 \rho_2}{1 - \rho_1 \rho_2} The frequency difference from peak-to-peak (or trough-to-trough) of the ripple is given by ΔΩ where \Delta \Omega = \frac{\pi}{T_d} \text{Overall Result} = \prod_{n=1}^N Vout_n This can give an overall response which is far from flat. As an example, a random collection of 25 cascaded (but separated) links give the result shown. Here, a random selection of path delays are assumed, with α taken as unity and ρ 1 and ρ 2 taking the typical value 0.15 (a return loss ≈ 16 dB), for the frequency range 10 to 20 GHz For this example, calibration at 50 MHz intervals would be advisable, in order to characterize this response. The ripple amplitude would be reduced if the mismatches ρ 1 and ρ 2 were improved but, especially if the lengths of the interconnecting links were made shorter. An RF chain, made up of surface mounted components, interconnected by stripline, which can be made physically small, may achieve less than 0.5 dB ripple. The use of integrated circuits would give lower ripple still (see, for example Monolithic microwave integrated circuit). \text{Mixer Output} = n\times F_\text{lo} \pm \ m\times F\text{sig} where m and n are integers. Usually, for a mixer, the desired output is the frequency with n = m = 1. The other outputs are often referred to as "spurs" and are usually unwanted. Frequency plans are often drawn up, often as a separate spreadsheet, to minimize the consequences of these unwanted signals Some general points regarding mixer performance are: Products with m and n small tend to have the largest amplitude so they require the most attention and, if possible, should fall outside the operational pass-band. Products when m and n are high tend to be of smaller amplitude and, often, can be ignored. Down-converters are best realized with F LO set high, i.e. F LO > F Sig . In receivers, image frequency signals are less troublesome if the IF (intermediate frequency) is set very high. Local oscillator leakage can be minimized by using double-balanced mixers Presenting large amplitude signals to a mixer should be avoided in order to avoid high level spurs. Consequently, it is poor practice to have high gain prior to a mixer (a requirement which may conflict with a need for a low overall noise figure). In any case, the LO power applied to the mixer should greatly exceed the signal power. In a typical mixer, the 1 dB compression point is between 5 and 10 dB below the local oscillator power. Note that the approximate relationship between IP3 and P1 differs from that for amplifiers. For mixers, a very approximate expression is: IP3(dB) \approx P1(dB) + 15(dB) As this is very approximate, it is advisable to refer to the specification of the mixer in question, for clarification. D_\text{R} = P_\text{max} - P_\text{sens} where P max is the maximum signal power, discussed earlier, and P sens is the smallest input power for signal detection (see Sensitivity, discussed earlier). P_\text{R} = A_\text{eff} \times P_\text{inc} Where A eff is the effective area of the antenna (or the Antenna aperture). Power density, which is in watts per metre squared, can be related to electric field strength E R , given in volts per metre, by E_\text{R} = \sqrt{P_\text{inc} \ 120 \pi} The gain of the antenna is related to the effective aperture by G = A_\text{eff} \frac{4 \pi}{ \lambda ^2} In practice, the effective aperture of the antenna is smaller than the actual physical area. For a dish, the effective area is about 0.5 to 0.6 times the actual area, and for a rectangular horn antenna it is about 0.7 to 0.8 times the actual area. For a dipole there is no actual physical area, but as a half-wave dipole has a power gain of 1.62 and the effective area can be inferred from that.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1315451869 under CC BY-SA 4.0; modifications have been made.