Rheological weldability

Rheological weldability (RW) of thermoplastics considers the materials flow characteristics in determining the weldability of the given material.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 4 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

Rheological weldability (RW) of thermoplastics considers the materials flow characteristics in determining the weldability of the given material. The process of welding thermal plastics requires three general steps, first is surface preparation.

The second step is the application of heat and pressure to create intimate contact between the components being joined and initiate inter-molecular diffusion across the joint and the third step is cooling. RW can be used to determine the effectiveness of the second step of the process for given materials. \gamma_{SG}\ =\gamma_{SL}+\gamma_{LG}\cos{\theta_{c}}, . \theta_C is the contact angle, and \gamma_{SG}\ , \gamma_{LG}\ , \gamma_{SL}\ represent surface tensions of the solid–gas, gas–liquid, and liquid–solid interfaces, respectively.

Where: \gamma_{SG} = Solid-Gas surface tension, \gamma_{SL} = Solid-Liquid surface tension, \gamma_{LG} = Liquid-Gas surface tension, \theta_{c} = Contact angle. For perfectly good wetting, contact angle (θ c ) at equilibrium should be minimized.

However, it is valid only at equilibrium, and rate of the equilibrium depends on the balance between driving force of wetting and viscosity of the liquid. In the case of polymer melts, viscosity can be very high and it may take a long time to reach the equilibrium contact angle (dynamic contact angle is likely higher than the contact angle at equilibrium).

Consequently, for the evaluation of weldability, viscosity of molten thermoplastics (polymer melts) have to be taken into account since welding is a rapid process. It can be said that the lower the viscosity during welding process (at welding temperature and pressure), the better the weldability.

Recalling that viscosity (η) decreases with increasing temperature (T) and shear rate ( \dot\gamma ) for most polymer melts, weldability is better where temperature and shear rate (movement) are higher within the entire cross-section of the welding region. \sigma = E\left(L-Lo\right)/Lo Where \sigma , or the stress experienced by the material and equals the change in length divided by the original length multiplied by the material's elasticity or Yong's modulus "E".

Plasticity

The lower a material's plasticity, the better the RW A material's ability to deform elastically while resisting flow is called plasticity. When an applied force or load exceeds the material's yield strength the material begins to deform plastically and the material will no longer return to its original shape.

During the welding processes of polymers, this is experienced at temperatures above the glass transition temperature and below the material's melting temperature.

Viscoelasticity

\eta = C \exp \left( \frac{-E_a}{RT} \right), Where: η is viscosity of molten polymer, C is pre-exponential factor, R is universal gas constant, T is absolute temperature. The absolute value of the activation energy (|E a |) can be calculated by taking the natural logarithm of the Arrhenius equation. (see Arrhenius equation).

Weldability of polymers

Welding of polymers is dependent on intimate contact resulting in molecular diffusion and chain entanglement across the weld joint. This action requires the polymer to be in a molten state where the melt viscosity and flow behavior have a drastic influence on the amount of diffusion and entanglement.

Therefore, the rheological weldability is best between materials with matching or very similar melting temperatures and melt viscosity. Also as a material's viscosity and activation energies are reduced the weldability of that material is improved.

For example, welding semi-crystalline to compatible semi-crystalline material and amorphous to compatible amorphous material have exhibited the best results. While a rheological analysis can provide reasonable insight to a material's weldability, in most cases production welding is typically prefaced with a series of tests to verify compatibility between both base materials as well as the process employed.

Similar to welding metals, the solidified polymer weld experiences residual stresses inherent to the joining process. With polymers, these residual stresses are in part due to the squeeze flow rate leading to a specific molecular alignment direction, ultimately influencing the weld strength and overall quality.

Having a thorough understanding of the rheological properties of the materials being joined can aid in determining the resultant residual stresses and in turn provide insight to processing methods that could reduce these stresses.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1357526077 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001357526077 · captured 2026-06-03 · not yet sealed in the ledger · verify the chain · version history

Cite this page as: encyclopegia.org, “Rheological weldability”, snapshot enwiki-001357526077. https://encyclopegia.org/a/rheological-weldability

Sources cited in this revision

1 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.