Schmitt trigger
≈ 11 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
of a Schmitt trigger. The horizontal and vertical axes are input voltage and output voltage, respectively. and are the switching thresholds, and and are the output voltage levels. In electronics, a Schmitt trigger is a comparator circuit with hysteresis implemented by applying positive feedback to the noninverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital output signal. The circuit is named a trigger because the output retains its value until the input changes sufficiently to cause a change. In the non-inverting configuration, when the input is higher than a chosen threshold, the output is high. When the input is below a different (lower) chosen threshold the output is low, and when the input is between the two levels the output retains its value. This dual threshold action is called hysteresis and implies that the Schmitt trigger possesses memory and can act as a bistable multivibrator (latch or flip-flop). There is a close relation between the two kinds of circuits: a Schmitt trigger can be converted into a latch and a latch can be converted into a Schmitt trigger. Schmitt trigger devices are typically used in signal conditioning applications to remove noise from signals used in digital circuits, particularly mechanical contact bounce in switches.…
of a Schmitt trigger. The horizontal and vertical axes are input voltage and output voltage, respectively. and are the switching thresholds, and and are the output voltage levels. In electronics, a Schmitt trigger is a comparator circuit with hysteresis implemented by applying positive feedback to the noninverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital output signal. The circuit is named a trigger because the output retains its value until the input changes sufficiently to cause a change. In the non-inverting configuration, when the input is higher than a chosen threshold, the output is high. When the input is below a different (lower) chosen threshold the output is low, and when the input is between the two levels the output retains its value. This dual threshold action is called hysteresis and implies that the Schmitt trigger possesses memory and can act as a bistable multivibrator (latch or flip-flop). There is a close relation between the two kinds of circuits: a Schmitt trigger can be converted into a latch and a latch can be converted into a Schmitt trigger. Schmitt trigger devices are typically used in signal conditioning applications to remove noise from signals used in digital circuits, particularly mechanical contact bounce in switches. They are also used in closed loop negative feedback configurations to implement relaxation oscillators, used in function generators and switching power supplies. (A) and a Schmitt trigger (B) on a noisy analog input signal (U). The green dotted lines are the circuit's switching thresholds. The Schmitt trigger tends to remove noise from the signal. In signal theory, a Schmitt trigger is essentially a one-bit quantizer.
History
The Schmitt trigger was invented by American scientist Otto Schmitt in 1934 while he was a graduate student, later described in his doctoral dissertation (1937) as a thermionic trigger. It was a direct result of Schmitt's study of the neural impulse propagation in squid nerves.
Implementation
Dynamic threshold (series feedback)
When the input voltage crosses the threshold in either direction, the circuit itself changes its own threshold to the opposite direction. For this purpose, it subtracts a part of its output voltage from the threshold (it is equal to adding voltage to the input voltage). Thus the output affects the threshold and does not affect the input voltage. These circuits are implemented by a differential amplifier with "series positive feedback" where the input is connected to the inverting input and the inverted output to the non-inverting input. In this arrangement, attenuation and summation are separated: a voltage divider acts as an attenuator and the loop acts as a simple series voltage summer (applying Kirchhoff's voltage law). Examples are the classic transistor emitter-coupled Schmitt trigger, the op-amp inverting Schmitt trigger, etc.
Modified input voltage (parallel feedback)
When the input voltage crosses the threshold in either direction the circuit changes its input voltage in the same direction (now it adds a part of its output voltage directly to the input voltage). Thus the output augments the input voltage and does not affect the threshold. These circuits can be implemented by a single-ended non-inverting amplifier with "parallel positive feedback" where the input and the output sources are connected through resistors to the input. The two resistors form a weighted parallel summer (applying Kirchhoff's current law) incorporating both the attenuation and summation. Examples are the less familiar collector-base coupled Schmitt trigger, the op-amp non-inverting Schmitt trigger, etc. Some circuits and elements exhibiting negative resistance can also act in a similar way: negative impedance converters (NIC), neon lamps, tunnel diodes (e.g., a diode with an N-shaped current–voltage characteristic in the first quadrant), etc. In the last case, an oscillating input will cause the diode to move from one rising leg of the "N" to the other and back again as the input crosses the rising and falling switching thresholds.
Two different unidirectional thresholds
Are assigned in this case to two separate open-loop comparators (without hysteresis) driving a bistable multivibrator (latch) or flip-flop. The trigger is toggled high when the input voltage crosses down to up the high threshold and low when the input voltage crosses up to down the low threshold. Again, there is a positive feedback, but now it is concentrated only in the memory cell. Examples are the 555 timer and the switch debouncing circuit. curve embedded in a buffer. Schmitt triggers can also be shown with inverting hysteresis curves and may be followed by bubbles. The documentation for the particular Schmitt trigger being used must be consulted to determine whether the device is non-inverting (i.e., where positive output transitions are caused by positive-going inputs) or inverting (i.e., where positive output transitions are caused by negative-going inputs). The symbol for Schmitt triggers in circuit diagrams is a triangle with a symbol inside representing its ideal hysteresis curve. V_\mathrm{HT} = \frac{R_\mathrm{E}}{R_\mathrm{E} + R_\mathrm{C2}}{V_+}\,. The output voltage is low but well above ground. It is approximately equal to the high threshold and may not be low enough to be a logical zero for subsequent digital circuits. This may require an additional level shifting circuit following the trigger circuit. V_\mathrm{LT} = \frac{R_\mathrm{E}}{R_\mathrm{E} + R_\mathrm{C1}}{V_+}\,. V_+ = \frac{R_2}{R_1 + R_2} \cdot V_\mathrm{in} + \frac{R_1}{R_1 + R_2} \cdot V_\mathrm{S}. The comparator will switch when . Then R_2 \cdot V_\mathrm{in} = -R_1 \cdot V_\mathrm{S} (the same result can be obtained by applying the current conservation principle). So V_\mathrm{in} must drop below -\frac{R_1}{R_2} V_\mathrm{S} to get the output to switch. Once the comparator output has switched to , the threshold becomes +\frac{R_1}{R_2} V_\mathrm{S} to switch back to high. So this circuit creates a switching band centered on zero, with trigger levels \pm\frac{R_1}{R_2} V_\mathrm{S} (it can be shifted to the left or the right by applying a bias voltage to the inverting input). The input voltage must rise above the top of the band, and then below the bottom of the band, for the output to switch on (plus) and then back off (minus). If R_1 is zero or R_2 is infinity (i.e., an open circuit), the band collapses to zero width, and it behaves as a standard comparator. The transfer characteristic is shown in the picture on the left. The value of the threshold is given by , and the maximum value of the output is the power supply rail. A unique property of circuits with parallel positive feedback is the impact on the input source. In circuits with negative parallel feedback (e.g., an inverting amplifier), the virtual ground at the inverting input separates the input source from the op-amp output. Here there is no virtual ground, and the steady op-amp output voltage is applied through the R_1{,}R_2 network to the input source. The op-amp output passes an opposite current through the input source (it injects current into the source when the input voltage is positive and it draws current from the source when it is negative). A practical Schmitt trigger with precise thresholds is shown in the figure on the right. The transfer characteristic has exactly the same shape of the previous basic configuration, and the threshold values are the same as well. On the other hand, in the previous case, the output voltage was depending on the power supply, while now it is defined by the Zener diodes (which could also be replaced with a single double-anode Zener diode). In this configuration, the output levels can be modified by appropriate choice of Zener diode, and these levels are resistant to power supply fluctuations (i.e., they increase the PSRR of the comparator). The resistor R_3 is there to limit the current through the diodes, and the resistor R_4 minimizes the input voltage offset caused by the comparator's input leakage currents . V_+ = \frac{R_1}{R_1 + R_2} \cdot V_\text{s}. The comparator will switch when . So V_\mathrm{in} must exceed this voltage to get the output to switch. Once the comparator output has switched to , the threshold becomes -\frac{R_1}{R_1 + R_2} V_\mathrm{S} to switch back to high. So this circuit creates a switching band centered on zero, with trigger levels \pm\frac{R_1}{R_1 + R_2} V_\mathrm{S} (it can be shifted to the left or the right by connecting R_1 to a bias voltage). The input voltage must rise above the top of the band, and then below the bottom of the band, for the output to switch off (minus) and then back on (plus). If R_1 is zero (i.e., a short circuit) or R_2 is infinity, the band collapses to zero width, and it behaves as a standard comparator. In contrast with the parallel version, this circuit does not impact on the input source, since the source is separated from the voltage divider output by the high op-amp input differential impedance. In the inverting amplifier voltage drop across resistor decides the reference voltages i.e., upper threshold voltage and lower threshold voltages for the comparison with input signal applied. These voltages are fixed, as the output voltage and resistor values are fixed. By changing the drop across , threshold voltages can be varied. By adding a bias voltage in series with resistor , drop across it can be varied, which can change threshold voltages. Desired values of reference voltages can be obtained by varying bias voltage. The above equations can be modified as: V_\pm = \pm V_\text{s} \frac{R_1}{R_1 + R_2} + V_\text{b} \frac{R_2}{R_1 + R_2}.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1362886435 under CC BY-SA 4.0; modifications have been made.