SMPTE timecode
≈ 6 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
SMPTE timecode ( or ) is a set of cooperating standards to label individual frames of video or film with a timecode. The system is defined by the Society of Motion Picture and Television Engineers in the SMPTE 12M specification. SMPTE revised the standard in 2008, turning it into a two-part document: SMPTE 12M-1 and SMPTE 12M-2, including new explanations and clarifications. A further revision, SMPTE 12M-3, expanded the standard to higher frame rates. Timecodes are added to film, video or audio material, and have also been adapted to synchronize music and theatrical production. They provide a time reference for editing, synchronization and identification. Timecode is a form of media metadata. The invention of timecode made modern videotape editing possible and led eventually to the creation of non-linear editing systems.
SMPTE timecode ( or ) is a set of cooperating standards to label individual frames of video or film with a timecode. The system is defined by the Society of Motion Picture and Television Engineers in the SMPTE 12M specification. SMPTE revised the standard in 2008, turning it into a two-part document: SMPTE 12M-1 and SMPTE 12M-2, including new explanations and clarifications. A further revision, SMPTE 12M-3, expanded the standard to higher frame rates. Timecodes are added to film, video or audio material, and have also been adapted to synchronize music and theatrical production. They provide a time reference for editing, synchronization and identification. Timecode is a form of media metadata. The invention of timecode made modern videotape editing possible and led eventually to the creation of non-linear editing systems. Drop-frame timecode originates from a compromise introduced when color NTSC video was invented. The NTSC designers wanted to retain compatibility with existing monochrome televisions. To minimize subcarrier visibility on a monochrome receiver, it was necessary to make the color subcarrier an odd multiple of half the line scan frequency; the multiple originally chosen was 495. With a 30 Hz frame rate the line scan frequency is (30 × 525) = 15750 Hz. So the subcarrier frequency would have been × 15750 = 3.898125 MHz. This was the subcarrier frequency originally chosen, but tests showed that on some monochrome receivers an interference pattern caused by the beat between the color subcarrier and the 4.5 MHz sound intercarrier could be seen. The visibility of this pattern could be greatly reduced by lowering the subcarrier frequency multiple to 455 (thus increasing the beat frequency from approximately 600 kHz to approximately 920 kHz) and by making the beat frequency also equal to an odd multiple of half the line scan frequency. This latter change could have been achieved by raising the sound intercarrier by 0.1% to 4.5045 MHz, but the designers, concerned that this might cause problems with some existing receivers, decided instead to reduce the color subcarrier frequency, and thus both the line scan frequency and the frame rate, by 0.1% instead. Thus the NTSC color subcarrier ended up as 3.579 MHz ( MHz), the line scan frequency as 15. kHz ( MHz) and the frame rate 29. Hz ( Hz). The altered frame rate meant that an hour of timecode at a nominal frame rate of was longer than an hour of wall-clock time by 3.6 seconds (for 29.97 non-drop timecode of 01:00:00:00 drop-frame timecode is 01:00:03;18 and for non-drop 00:59:56:12 drop-frame is 01:00:00;00), leading to an error of almost a minute and a half over a day. To correct this, drop-frame SMPTE timecode was invented. In spite of what the name implies, no video frames are dropped or skipped when using drop-frame timecode. Rather, some of the timecodes are dropped. In order to make an hour of timecode match an hour on the clock, drop-frame timecode skips frame numbers 0 and 1 of the first second of every minute, except when the number of minutes is divisible by ten. This causes timecode to skip 18 frames each ten minutes (18,000 frames @ ) and almost perfectly compensates for the difference in rate (but still accumulates 1 frame every 9 hours 15 minutes). For example, the sequence when frame counts are dropped: 01:08:59:28 01:08:59:29 01:09:00:02 01:09:00:03 For each tenth minute 01:09:59:28 01:09:59:29 01:10:00:00 01:10:00:01 While non-drop timecode is displayed with colons separating the digit pairs—"HH:MM:SS:FF"—drop-frame is usually represented with a semicolon (;) or period (.) as the divider between all the digit pairs—HH;MM;SS;FF, HH.MM.SS.FF—or just between the seconds and frames—HH:MM:SS;FF or HH:MM:SS.FF. Drop-frame timecode is typically abbreviated as DF and non-drop as NDF. Bit 10 of the SMPTE timecode frame is designated the Drop Frame Flag, and when set, indicates that the timecode should obey the drop frame rules.
History
There were several iterations of timecode in the late 1960s (EECO, DaVinci, Siemens, etc.). The version adopted by SMPTE was developed by Leo O'Donnell while he was working for the National Film Board of Canada. O'Donnell's version referenced time of day and used an 80-bit word that was derived from rocket telemetry. There were several patents issued on this version (US3877799, for example). Since that time, several changes have been made by SMPTE to keep up with technology, including extensions to accommodate high frame rate material.
See also
Field dominance IRIG timecode Linear timecode MIDI timecode Rewritable consumer timecode Vertical interval timecode
Notes
References
Text derived from https://en.wikipedia.org/w/index.php?oldid=1378213461 under CC BY-SA 4.0; modifications have been made.