---
title: Switch virtual interface
slug: switch-virtual-interface
qid: 
snapshot: enwiki-001324606272
content_hash: 
license: CC BY-SA 4.0
source: https://en.wikipedia.org/w/index.php?oldid=1324606272
tags: [20474387, 23069423, 23118434, 23468805, 23603337, 24745114, 26698221]
---

# Switch virtual interface

> [!note] Provenance
> Snapshot `enwiki-001324606272` · content root `…`
> Derived from <https://en.wikipedia.org/w/index.php?oldid=1324606272> · Licensed CC BY-SA 4.0

A switch virtual interface (SVI) or routed VLAN interface (RVI) is a virtual network interface that represents a logical layer-3 interface on a multilayer network switch. VLANs divide broadcast domains in a local area network (LAN) environment. Whenever hosts in one VLAN need to communicate with hosts in another VLAN, the traffic must be routed between them. This is known as inter-VLAN routing. On layer-3 switches it is accomplished by the creation of layer-3 interfaces (SVIs). An SVI is a virtual routed interface that connects a VLAN on the device to the Layer 3 router engine on the same device. Only one VLAN interface can be associated with a VLAN, but you need to configure a VLAN interface for a VLAN only when you want to route between VLANs or to provide IP host connectivity to the device through a virtual routing and forwarding (VRF) instance that is not the management VRF. When you enable VLAN interface creation, a switch creates a VLAN interface for the default VLAN (VLAN 1) to permit remote switch administration. SVIs are generally configured for a VLAN for the following reasons: * To allow traffic to be routed between VLANs by providing a default gateway for the VLAN. * To provide fallback bridging (if required for non-routable protocols). * To provide Layer 3 IP connectivity to the switch. * To support bridging configurations and routing protocol.…

A switch virtual interface (SVI) or routed VLAN interface (RVI) is a virtual network interface that represents a logical layer-3 interface on a multilayer network switch. VLANs divide broadcast domains in a local area network (LAN) environment. Whenever hosts in one VLAN need to communicate with hosts in another VLAN, the traffic must be routed between them. This is known as inter-VLAN routing. On layer-3 switches it is accomplished by the creation of layer-3 interfaces (SVIs). An SVI is a virtual routed interface that connects a VLAN on the device to the Layer 3 router engine on the same device. Only one VLAN interface can be associated with a VLAN, but you need to configure a VLAN interface for a VLAN only when you want to route between VLANs or to provide IP host connectivity to the device through a virtual routing and forwarding (VRF) instance that is not the management VRF. When you enable VLAN interface creation, a switch creates a VLAN interface for the default VLAN (VLAN 1) to permit remote switch administration. SVIs are generally configured for a VLAN for the following reasons: To allow traffic to be routed between VLANs by providing a default gateway for the VLAN. To provide fallback bridging (if required for non-routable protocols). To provide Layer 3 IP connectivity to the switch. To support bridging configurations and routing protocol. To provide an access layer - 'Routed Access' Configuration (in lieu of Spanning Tree Protocol) Advantages include: Much faster than router-on-a-stick, because everything is hardware-switched and -routed. No need for external links from the switch to a router for routing. Not limited to one link. Layer 2 EtherChannels can be used between the switches to get more bandwidth. Latency is much lower, because it does not need to leave the switch. ==References== Cisco Systems, Configure InterVLAN Routing on Layer 3 Switches Cisco Systems, Configuring SVI Cisco Systems, 2006, "Building Cisco Multilayer Switched Networks" (Version 3.0), Cisco Systems Inc. Switch Virtual Interfaces (SVI) configuration Data Centre Networking Module (COMH9003) | Cork Institute of Technology
