Toughening

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In materials science, toughening refers to the process of making a material more resistant to the propagation of cracks. When a crack propagates, the associated irreversible work in different materials classes is different. Thus, the most effective toughening mechanisms differ among different materials classes.

The crack tip plasticity is important in toughening of metals and long-chain polymers. Ceramics have limited crack tip plasticity and primarily rely on different toughening mechanisms.

In materials science, toughening refers to the process of making a material more resistant to the propagation of cracks. When a crack propagates, the associated irreversible work in different materials classes is different. Thus, the most effective toughening mechanisms differ among different materials classes.

The crack tip plasticity is important in toughening of metals and long-chain polymers. Ceramics have limited crack tip plasticity and primarily rely on different toughening mechanisms.

G_{\Iota C} = B\sigma_{yf}\epsilon_{fr}\rho where G_{\Iota C} is the plane strain toughness, B is a constant that incorporates the stress state, \sigma_{yf} is the tensile flow stress at fracture, \epsilon_{fr} is the tensile fracture strain, and \rho is the radius of crack tip. In a low yield strength material, the crack tip can be blunted easily and larger crack tip radius is formed.

Thus, in a given metallic alloy, toughness in a low-strength condition is usually higher than for higher strength conditions because less plasticity is available for toughening. Therefore, some safety-critical structural part such as pressure vessels and pipelines to aluminum alloy air frames are manufactured in relatively low strength version.

Nonetheless, toughness should be improved without sacrificing its strength in metal. Designing a new alloy or improving its processing can achieve this goal. Designing a new alloy can be explained by different toughness in several ferrous alloy.18%Ni-maraging steel has a higher toughness than the martensitic steel AISI 4340.

In an AISI 4340 alloy, interstitial carbon exist in a bcc (body centered cubic) matrix and show an adverse effect on toughness. In 18%Ni-maraging steel, the carbon content is lower and martensite is strengthened by substitutional Ni atoms. In addition, transformation induced plasticity (TRIP) effects in steel can provide additional toughness.

In TRIP steel, matrix is metastable and can be transformed to martensite during deformation. The work associated to phase transformation contributes to the improvement of toughness. In a monolithic Pd–Ag–P–Si–Ge glass alloy, the properties of high bulk modulus and low shear modulus lead to proliferation of shear bands.

These bands are self constrained and the toughness is improved. Metals can be toughened by improvement of processing. With a high affinity for oxygen, titanium alloy can absorb oxygen easily.

Oxygen can promote the formation of α 2 phase. These coherent α 2 particles lead to easy crack nucleation and fast crack propagation within the planar slip bands. Therefore, toughness of titanium alloy is decreased.

Multiple vacuum arc melting (VAR) technique can be used to minimize the oxygen content and increase the toughness of the alloy. Similarly, phosphorus in steels can decrease toughness dramatically. Phosphorus can segregate on grain boundary and lead to intergranular fracture.

If the dephosphorization is improved during steelmaking, the steel will be toughened for a lower phosphorus content. After appropriate processing of steel, crystalline grains and second phases that are oriented along rolling direction can improve toughness of materials by delamination which can relax triaxial stress and blunt the crack tip.

Metals can also be strengthened by the methods described below for ceramics, but these methods generally have a lesser impact on toughening than plasticity induced crack blunting. G_{C}= V_m G_{m}+V_f G_{f}+\Delta G_{C} where G_{ m} and G_{f} are toughness of matrix and fibers respectively, V_{ m} and V_{ f} are volume of matrix and fibers respectively, \Delta G_{C} is the additional toughness caused by bridging toughening.

After crack propagates across through fiber, the fiber is elongated and is pulled out from matrix. These processes correspond to plastic deformation and pull-out work and contribute to toughening of composite. When fiber is brittle, the pull-out work dominates the irreversible work contributing to toughening.

The increment of toughness caused by pull-out work can be expressed by: \Delta G_{C} = {1\over 32}{\beta^2\sigma_{f}^2 V_f d \over \tau} where \beta is the ratio between debond length and critical length, \sigma_{f} is the strength of fibers, d is the width of fiber, V_f is the fraction of fibers and \tau is the interface friction stress. From the equation, it can be found that higher volume fraction, higher fiber strength and lower interfacial stress can get a better toughening effect. \Delta G_{C} = C\sigma_{y}\epsilon_f V_f l_d where C is a constant between 1.5-6, \sigma_{y} is the flow stress of fibers, \epsilon_{y} is the fracture strain of fibers, V_f is the fraction of fibers, and l_d is the debond length.

From the equation, it can be found that higher flow stress and longer debond length can improve the toughening. However, longer debond length usually lead to a decrease of flow stress because of loss of constraint for plastic deformation.

The toughness in a composite with ductile phase toughening can also be shown using stress intensity factor, K_c by linear superposition of the matrix and crack bridging based on solutions by Tada. This model can predict behavior for small-scale bridging (bridge length K_c = K_m + \Delta K_b = K_m + \sqrt{\frac{2}{\pi}}\alpha V_f\int_{0}^{L}\frac{\sigma_y}{\sqrt{x}}dx where K_m is the fracture toughness of the matrix, \Delta K_b is the toughening due to crack bridging, L is the bridge length, x is the distance behind the crack tip, \sigma_y is the uniaxial yield stress, and \alpha is a constraint/ triaxiality factor.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1314094963 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot enwiki-001314094963 · captured 1759162393.0 · version history

Cite this page as: encyclopegia.org, “Toughening”, snapshot enwiki-001314094963. https://encyclopegia.org/a/toughening

Sources cited in this revision

5 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.