toughness

Uses your system voice; voice and rate in settings.

Q486802Snapshot

≈ 4 min read

Names in other languages

  • skPrierazuvzdornosť
  • Русскийударная вязкость
  • Portuguêstenacidade
  • Englishtoughness
  • Françaisténacité
  • Polskiwiązkość
  • 简体中文韧性
  • 繁體中文韌性
  • 中文韌性

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In materials science and metallurgy, toughness is the ability of a material to absorb energy and plastically deform without fracturing. Toughness is the strength with which the material opposes rupture. One definition of material toughness is the amount of energy per unit volume that a material can absorb before rupturing. This measure of toughness is different from that used for fracture toughness, which describes the capacity of materials to resist fracture. Toughness requires a balance of strength and ductility.

In materials science and metallurgy, toughness is the ability of a material to absorb energy and plastically deform without fracturing. Toughness is the strength with which the material opposes rupture. One definition of material toughness is the amount of energy per unit volume that a material can absorb before rupturing. This measure of toughness is different from that used for fracture toughness, which describes the capacity of materials to resist fracture. Toughness requires a balance of strength and ductility.

Toughness and strength

Toughness is related to the area under the stress–strain curve. In order to be tough, a material must be both strong and ductile. For example, brittle materials (like ceramics) that are strong but with limited ductility are not tough; conversely, very ductile materials with low strengths are also not tough. To be tough, a material should withstand both high stresses and high strains. Generally speaking, strength indicates how much force the material can support, while toughness indicates how much energy a material can absorb before rupturing.

Mathematical definition

Toughness can be determined by integrating the stress-strain curve. It is the energy absorbed during plastic deformation per unit volume prior to fracture. The explicit mathematical description is: \tfrac{\mbox{energy}}{\mbox{volume}} = \int_{0}^{\varepsilon_f} \sigma\, d\varepsilon where \varepsilon is strain \varepsilon_f is the strain upon failure \sigma is stress If the upper limit of integration up to the yield point is restricted, the energy absorbed per unit volume is known as the modulus of resilience. Mathematically, the modulus of resilience can be expressed by the product of the square of the yield stress divided by two times the Young's modulus of elasticity. That is,

Toughness tests

The toughness of a material can be measured using a small specimen of that material. A typical testing machine uses a pendulum to deform a notched specimen of defined cross-section. The height from which the pendulum fell, minus the height to which it rose after deforming the specimen, multiplied by the weight of the pendulum, is a measure of the energy absorbed by the specimen as it was deformed during the impact with the pendulum. The Charpy and Izod notched impact strength tests are typical ASTM tests used to determine toughness.

Unit of toughness

Tensile toughness (or deformation energy, U T ) is measured in units of joule per cubic metre (J·m −3 ), or equivalently newton-metre per cubic metre (N·m·m −3 ), in the SI system and inch-pound-force per cubic inch (in·lbf·in −3 ) in US customary units: 1.00 N·m·m −3 ≃  in·lbf·in −3 1.00 in·lbf·in −3 ≃ 6.89 kN·m·m −3 . In the SI system, the unit of tensile toughness can be easily calculated by using area underneath the stress–strain (σ–ε) curve, which gives tensile toughness value, as given below: U T = Area underneath the stress–strain (σ–ε) curve = σ × ε U T [=] F/A × ΔL/L = (N·m −2 )·(unitless) U T [=] N·m·m −3 U T [=] J·m −3

See also

Hardness Rubber toughening Shock (mechanics) Tablet hardness testing

References

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376633261 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

No external citation was extracted for this revision. That is a statement about the source, not a claim that none exists.