Universal joint

A universal joint (also called a universal coupling or U-joint) is a joint or coupling connecting rigid shafts whose axes are inclined to each other.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 7 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

A universal joint (also called a universal coupling or U-joint) is a joint or coupling connecting rigid shafts whose axes are inclined to each other. It is commonly used in shafts that transmit rotary motion. It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft.

The universal joint is not a constant-velocity joint. U-joints are also sometimes called by various eponymous names, as follows: * Cardan joint, after Gerolamo Cardano, a polymath of the 16th century who contributed to knowledge of various clever mechanisms, including gimbals * Hooke joint or Hooke's joint, after Robert Hooke, a polymath of the 17th century who contributed to knowledge of various clever mechanisms * Spicer joint, after Clarence W. Spicer and the Spicer Manufacturing Company, who manufactured U joints * Hardy Spicer joint, after the Hardy Spicer brand, a successor to the Spicer brand

A universal joint (also called a universal coupling or U-joint) is a joint or coupling connecting rigid shafts whose axes are inclined to each other. It is commonly used in shafts that transmit rotary motion. It consists of a pair of hinges located close together, oriented at 90° to each other, connected by a cross shaft.

The universal joint is not a constant-velocity joint. U-joints are also sometimes called by various eponymous names, as follows: Cardan joint, after Gerolamo Cardano, a polymath of the 16th century who contributed to knowledge of various clever mechanisms, including gimbals Hooke joint or Hooke's joint, after Robert Hooke, a polymath of the 17th century who contributed to knowledge of various clever mechanisms Spicer joint, after Clarence W. Spicer and the Spicer Manufacturing Company, who manufactured U joints Hardy Spicer joint, after the Hardy Spicer brand, a successor to the Spicer brand \hat{\mathbf{x}}_1 = \left[\cos\gamma_1\,,\, \sin\gamma_1\,,\,0\right] \hat{\mathbf{x}}_2 is confined to the "blue plane" in the diagram and is the result of the unit vector on the x axis \hat{x} = [1, 0, 0] being rotated through Euler angles \left[\tfrac{\pi}{2}\,,\, \beta\,,\, \gamma_2\right] : \hat{\mathbf{x}}_2 = \left[-\cos\beta\sin\gamma_2\,,\, \cos\gamma_2\,,\, \sin\beta\sin\gamma_2\right] A constraint on the \hat{\mathbf{x}}_1 and \hat{\mathbf{x}}_2 vectors is that since they are fixed in the gimbal, they must remain at right angles to each other.

This is so when their dot product equals zero: \hat{\mathbf{x}}_1 \cdot \hat{\mathbf{x}}_2 = 0 Thus the equation of motion relating the two angular positions is given by: \tan\gamma_1 = \cos\beta\tan\gamma_2\, with a formal solution for \gamma_2 = \arctan\left[\tan\gamma_1 \sec\beta\right]\, The solution for \gamma_2 is not unique since the arctangent function is multivalued, however it is required that the solution for \gamma_2 be continuous over the angles of interest. For example, the following explicit solution using the atan2(y,x) function will be valid for -\pi : \gamma_2 = \operatorname{atan2}\left(\sin\gamma_1, \cos\beta\, \cos\gamma_1\right) The angles \gamma_1 and \gamma_2 in a rotating joint will be functions of time.

Differentiating the equation of motion with respect to time and using the equation of motion itself to eliminate a variable yields the relationship between the angular velocities \omega_1 = \frac{d\gamma_1}{dt} and \omega_2 = \omega_1\left(\frac{\cos\beta}{1 - \sin^2\beta\,\cos^2\gamma_1}\right) As shown in the plots, the angular velocities are not linearly related, but rather are periodic with a period half that of the rotating shafts. The angular velocity equation can again be differentiated to get the relation between the angular accelerations a_1 and a_2 = \frac{a_1\cos\beta}{1 - \sin^2\beta\,\cos^2\gamma_1} - \frac{\omega_1^2\cos\beta\,\sin^2\beta\,\sin 2\gamma_1}{\left(1 - \sin^2\beta\,\cos^2\gamma_1\right)^2}

Double Cardan shaft

A configuration known as a double Cardan joint drive shaft partially overcomes the problem of jerky rotation. This configuration uses two U-joints joined by an intermediate shaft, with the second U-joint phased in relation to the first U-joint to cancel the changing angular velocity.

In this configuration, the angular velocity of the driven shaft will match that of the driving shaft, provided that both the driving shaft and the driven shaft are at equal angles with respect to the intermediate shaft (but not necessarily in the same plane) and that the two universal joints are 90 degrees out of phase. This assembly is commonly employed in rear wheel drive vehicles, where it is known as a drive shaft or propeller (prop) shaft.

Even when the driving and driven shafts are at equal angles with respect to the intermediate shaft, if these angles are greater than zero, oscillating moments are applied to the three shafts as they rotate. These tend to bend them in a direction perpendicular to the common plane of the shafts.

This applies forces to the support bearings and can cause "launch shudder" in rear wheel drive vehicles. The intermediate shaft will also have a sinusoidal component to its angular velocity, which contributes to vibration and stresses.

Mathematically, this can be shown as follows: If \gamma_1\, and \gamma_2\, are the angles for the input and output of the universal joint connecting the drive and the intermediate shafts respectively, and \gamma_3\, and \gamma_4\, are the angles for the input and output of the universal joint connecting the intermediate and the output shafts respectively, and each pair are at angle \beta\, with respect to each other, then: \tan\gamma_2 = \cos\beta\,\tan\gamma_1\qquad \tan\gamma_4 = \cos\beta\,\tan\gamma_3 If the second universal joint is rotated 90 degrees with respect to the first, then Using the fact that \tan\left(\gamma + \tfrac{\pi}{2}\right) = \frac{1}{\tan\gamma} yields: \tan\gamma_4 = \frac{\cos\beta}{\tan\gamma_2} = \frac{1}{\tan\gamma_1} = \tan\left(\gamma_1 + \tfrac{\pi}{2}\right)\, and it is seen that the output drive is just 90 degrees out of phase with the input shaft, yielding a constant-velocity drive. NOTE: The reference for measuring angles of input and output shafts of universal joint are mutually perpendicular axes.

So, in absolute sense the forks of the intermediate shaft are parallel to each other. (Since, one fork is acting as input and the other fork is acting as output for shafts and above 90 degree phase difference is mentioned between the forks.)

Double Cardan joint

A double Cardan joint consists of two universal joints mounted back to back with a centre yoke; the centre yoke replaces the intermediate shaft. Provided that the angle between the input shaft and centre yoke is equal to the angle between the centre yoke and the output shaft, the second Cardan joint will cancel the velocity errors introduced by the first Cardan joint and the aligned double Cardan joint will act as a CV joint.

Thompson coupling

A Thompson coupling is a refined version of the double Cardan joint. It offers slightly increased efficiency with the penalty of great increase in complexity.

Notes

Thompson Couplings Limited explanation of the Thompson coupling. Universal Joint Failure - Custom Solutions Address Common Problems Universal Joint Phasing - The Concept and Importance of Universal Joint Phasing and Drive Shaft Alignment The Thompson Coupling - invented by Glenn Thompson by ABC Television (The New Inventors, broadcast Feb 2007). (constant-velocity coupling).

About universal joints at McMaster Carr. Cardan Shaft at McMaster Carr.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1374673293 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

17 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.