Upper mantle
≈ 7 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
The upper mantle of Earth is a very thick layer of rock inside the planet, which begins just beneath the crust (at about under the oceans, and about under the continents) and ends at the top of the lower mantle, at about . Temperatures range from around at the upper boundary with the crust to around at the boundary with the lower mantle. Upper mantle material that has come up onto the surface comprises about 55% olivine, 35% pyroxene, and 5–10% of calcium oxide and aluminum oxide minerals such as plagioclase, spinel, or garnet, depending on depth.
The upper mantle of Earth is a very thick layer of rock inside the planet, which begins just beneath the crust (at about under the oceans, and about under the continents) and ends at the top of the lower mantle, at about . Temperatures range from around at the upper boundary with the crust to around at the boundary with the lower mantle. Upper mantle material that has come up onto the surface comprises about 55% olivine, 35% pyroxene, and 5–10% of calcium oxide and aluminum oxide minerals such as plagioclase, spinel, or garnet, depending on depth.
Lehmann discontinuity
The Lehmann discontinuity is an abrupt increase of P-wave and S-wave velocities at a depth of (Note that this is a different "Lehmann discontinuity" than the one between the Earth's inner and outer cores labeled in the image on the right.)
Transition zone
The transition zone is located between the upper mantle and the lower mantle between a depth of and . This is thought to occur as a result of the rearrangement of grains in olivine to form a denser crystal structure as a result of the increase in pressure with increasing depth. Below a depth of , due to pressure changes, ringwoodite minerals change into two new denser phases, bridgmanite and periclase. This can be seen using body waves from earthquakes, which are converted, reflected, or refracted at the boundary, and predicted from mineral physics, as the phase changes are temperature and density-dependent and hence depth-dependent.
410 km discontinuity
A single peak is seen in all seismological data at , which is predicted by the single transition from α- to β- Mg 2 SiO 4 (olivine to wadsleyite). From the Clapeyron slope this discontinuity is expected to be shallower in cold regions, such as subducting slabs, and deeper in warmer regions, such as mantle plumes.
670 km discontinuity
This is the most complex discontinuity and marks the boundary between the upper and lower mantle. It appears in PP precursors (a wave that reflects off the discontinuity once) only in certain regions but is always apparent in SS precursors. It is seen as single and double reflections in receiver functions for P to S conversions over a broad range of depths (640–720 km, or 397–447 mi). The Clapeyron slope predicts a deeper discontinuity in colder regions and a shallower discontinuity in hotter regions. This discontinuity is generally linked to the transition from ringwoodite to bridgmanite and periclase. This is thermodynamically an endothermic reaction and creates a viscosity jump. Both characteristics cause this phase transition to play an important role in geodynamical models.
Other discontinuities
There is another major phase transition predicted at for the transition of olivine (β to γ) and garnet in the pyrolite mantle. This one has only sporadically been observed in seismological data. Other non-global phase transitions have been suggested at a range of depths.
Temperature and pressure
Temperatures range from approximately at the upper boundary with the crust to approximately at the core-mantle boundary. The highest temperature of the upper mantle is . Although the high temperature far exceeds the melting points of the mantle rocks at the surface, the mantle is almost exclusively solid. The enormous lithostatic pressure exerted on the mantle prevents melting because the temperature at which melting begins (the solidus) increases with pressure.
Pressure increases as depth increases since the material beneath has to support the weight of all the material above it. The entire mantle is thought to deform like a fluid on long timescales, with permanent plastic deformation. The highest pressure of the upper mantle is compared to the bottom of the mantle, which is . Estimates for the viscosity of the upper mantle range between 10 19 and 10 24 Pa·s, depending on depth, temperature, composition, state of stress, and numerous other factors. The upper mantle can only flow very slowly.
However, when large forces are applied to the uppermost mantle, it can become weaker, and this effect is thought to be important in allowing the formation of tectonic plate boundaries. Although there is a tendency to larger viscosity at greater depth, this relation is far from linear and shows layers with dramatically decreased viscosity, in particular in the upper mantle and at the boundary with the core.
Mineral composition
mantle mineralogy as a function of mineral volume fraction and depth variation. The seismic data is not sufficient to determine the composition of the mantle. Observations of rocks exposed on the surface and other evidence reveal that the upper mantle is mafic minerals olivine and pyroxene, and it has a density of about Upper mantle material that has come up onto the surface comprises about 55% olivine and 35% pyroxene, and 5 to 10% of calcium oxide and aluminum oxide.
The upper mantle is dominantly peridotite, composed primarily of variable proportions of the minerals olivine, clinopyroxene, orthopyroxene, and an aluminous phase. The aluminous phase is plagioclase in the uppermost mantle, then spinel, and then garnet below about . Gradually through the upper mantle, pyroxenes become less stable and transform into majoritic garnet. Experiments on olivines and pyroxenes show that these minerals change the structure as pressure increases at greater depth, which explains why the density curves are not perfectly smooth.
When there is a conversion to a more dense mineral structure, the seismic velocity rises abruptly and creates a discontinuity. At the top of the transition zone, olivine undergoes isochemical phase transitions to wadsleyite and ringwoodite. Unlike nominally anhydrous olivine, these high-pressure olivine polymorphs have a large capacity to store water in their crystal structure. This has led to the hypothesis that the transition zone may host a large quantity of water.
In Earth's interior, olivine occurs in the upper mantle at depths less than , and ringwoodite is inferred within the transition zone from about depth. Seismic activity discontinuities at about , , and depth have been attributed to phase changes involving olivine and its polymorphs. At the base of the transition zone, ringwoodite decomposes into bridgmanite (formerly called magnesium silicate perovskite), and ferropericlase. Garnet also becomes unstable at or slightly below the base of the transition zone.
Kimberlites explode from the earth's interior and sometimes carry rock fragments. Some of these xenolithic fragments are diamonds that can only come from the higher pressures below the crust. The rocks that come with this are ultramafic nodules and peridotite.
Chemical composition
The composition seems to be very similar to the crust. One difference is that rocks and minerals of the mantle tend to have more magnesium and less silicon and aluminum than the crust. The first four most abundant elements in the upper mantle are oxygen, magnesium, silicon, and iron.
References
Text derived from https://en.wikipedia.org/w/index.php?oldid=1351963283 under CC BY-SA 4.0; modifications have been made.