USB hardware

Uses your system voice; voice and rate in settings.

Snapshot

≈ 28 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

The initial versions of the USB standard specified connectors that were easy to use and would have long life spans; revisions of the standard added smaller connectors useful for compact portable devices. Higher-speed development of the USB standard gave rise to another family of connectors to permit additional data links. All versions of USB specify cable properties. Version 3.x cables, marketed as SuperSpeed, added a data link; namely, in 2008, USB 3.0 added a full-duplex lane (two twisted pairs of wires for one differential signal of serial data per direction), and in 2014, the USB-C specification added a second full-duplex lane. USB has always included some capability of providing power to peripheral devices, but the amount of power that can be given has increased over time. The modern specifications are called USB Power Delivery (USB-PD) and allow up to 240 watts. Initially USB 1.0/2.0 provided up to 2.5 W, USB 3.0 provided up to 4.5 W, and subsequent Battery Charging (BC) specifications provided power up to 7.5 W. The modern Power Delivery specifications began with USB PD 1.0 in 2012, providing for power delivery up to 60 watts; PD 2.0 version 1.2 in 2013, along with USB 3.1, up to 100 W; and USB PD 3.1 in 2021 raised the maximum to 240 W.…

The initial versions of the USB standard specified connectors that were easy to use and would have long life spans; revisions of the standard added smaller connectors useful for compact portable devices. Higher-speed development of the USB standard gave rise to another family of connectors to permit additional data links. All versions of USB specify cable properties. Version 3.x cables, marketed as SuperSpeed, added a data link; namely, in 2008, USB 3.0 added a full-duplex lane (two twisted pairs of wires for one differential signal of serial data per direction), and in 2014, the USB-C specification added a second full-duplex lane. USB has always included some capability of providing power to peripheral devices, but the amount of power that can be given has increased over time. The modern specifications are called USB Power Delivery (USB-PD) and allow up to 240 watts. Initially USB 1.0/2.0 provided up to 2.5 W, USB 3.0 provided up to 4.5 W, and subsequent Battery Charging (BC) specifications provided power up to 7.5 W. The modern Power Delivery specifications began with USB PD 1.0 in 2012, providing for power delivery up to 60 watts; PD 2.0 version 1.2 in 2013, along with USB 3.1, up to 100 W; and USB PD 3.1 in 2021 raised the maximum to 240 W. USB has been selected as the charging format for many mobile phones and other peripheral devices and hubs, reducing the proliferation of proprietary chargers. Since USB 3.1 USB-PD is part of the USB standard. The latest PD versions can also provide power to lower power laptops. A standard USB-C cable can carry at least 60 watts and at least of USB 2.0 (480 Mbit/s half-duplex). In 2019, USB4, which uses only the USB-C connector, added connection-oriented video and audio abilities (DisplayPort) and compatibility with Thunderbolt 3 and later.

Connectors

USB implements a tiered star-like network topology. Unlike other data buses (such as Ethernet), USB connections are directional. Ports are classified as either downstream-facing ports (DFP), or upstream-facing ports (UFP), though there are also those that can be dual-role. Ports on a host, and those on a hub into which devices are connected, are DFP, while ports on devices, and a port on a hub used to connect it to a host, are UFP. Only downstream-facing ports originally provided power by default. This topology was chosen to easily prevent electrical overload and damage to equipment. Prior to the introduction of Type-C, USB receptacles and their plugs had physically distinct shapes for different roles (DFP, UFP, and dual-role), preventing the possibility of two hosts erroneously being connected together. DFP receptacles and their corresponding plugs were known as Type-A; UFP receptacles and their corresponding plugs were known as Type-B; while those that were dual role were known as Type-AB. Consequently, a standards-conforming USB cable with such legacy plugs on both ends would have had a Type-A plug on one end, and a Type-B plug on the other. USB extension cables with a Type-A plug on one end and a Type-A port on the other existed but these were not compliant with USB standards. A Type-AB receptacle accepted both Type-A and Type-B plugs, and a device with such a receptacle took either a DFP or UFP role according to the type of plug attached. With the introduction of Type‑C came transitional cables: a Type‑C plug at one end and a Type-A or a Type-B plug at the other. These transitional cables are still directional, and in such a cable the Type‑C plug is electrically marked as either A or B as appropriate to complement the opposite connector. The modern standard is a cable with a Type-C plug on each end; these cables are non-directional, and connected devices instead negotiate their respective roles. Legacy plugs and receptacles (types A, B and AB) came in three different sizes: The original Standard size; Mini, which was the first attempt to accommodate handheld mobile equipment (now mostly deprecated); and Micro. All of these were superseded in 2014 by Type‑C, which is required for operational modes with two lanes (USB 3.2 1×2 (10 Gbit/s), USB 3.2 2×2 (20 Gbit/s), or any USB4 modes) and allows power up to 240 watts in either direction. Before USB4, there were five speeds for USB data transfer: Low-Speed; Full-Speed (both USB 1.0 and 1.1); High-Speed (USB 2.0); SuperSpeed (USB 3.0, later designated as USB 3.2 Gen 1×1); and SuperSpeed+ (designated as USB 3.1 Gen 2, later as USB 3.2 Gen 2×1). Legacy connectors have differing hardware and cabling requirements for the first three generations of the standard (USB 1.x, USB 2.0, and USB 3.x). USB devices have some choice of implemented modes, and since USB 3.1 the USB revision alone does not sufficiently designate implemented modes. Which capabilities a device supports are defined by the device's chipset or included SoC and the OS's supported drivers (therefore one must check the full names of the supported USB operation modes in the device's specification; the printed icons usually do not specify all modes, or precisely enough). In the USB 3 specifications it is recommended that the insulators visible inside Standard‑A SuperSpeed plugs and receptacles be a specific blue color (Pantone 300 C). In Standard‑A receptacles with support for the 10 Gbit/s (Gen 2) signaling rate introduced in USB 3.1, some makers instead use a teal blue color, but the standards recommend the same blue for all SuperSpeed-capable Standard‑A receptacles, including those capable of the higher rate.

Type‑C (USB-C)

receptacle (left) and plug (right) The USB-C connector supersedes all earlier USB connectors, the Mini DisplayPort connector (used for earlier Thunderbolt), and, since 2025, the Lightning connector. It is used for all USB protocols and for Thunderbolt (3 and later), DisplayPort (1.2 and later), and others. Developed at roughly the same time as the USB 3.1 specification, but distinct from it, the USB-C Specification 1.0 was finalized in August 2014 and defined a new small reversible connector for all USB and some other devices. The USB-C plug connects both to hosts and to peripheral devices, as well as to chargers and power supplies, replacing all of the preceding USB connectors with a standard meant to be future-proof. The 24-pin double-sided connector provides four power–ground pairs, two differential pairs for USB 2.0 data (though only one pair is implemented in a USB-C cable), four pairs for SuperSpeed data bus (only two pairs are used in USB 3.1 mode), two "sideband use" pins, V CONN +5 V power for active cables, and a configuration pin for cable orientation detection and dedicated biphase mark code (BMC) configuration data channel (CC). Type-A and Type-B adaptors and cables are required for older hosts and devices to plug into USB-C hosts and devices. Adapters and cables with a USB-C receptacle are not allowed. A Full-Featured USB cable is a Type‑C-to-Type‑C cable that supports USB 2.0, USB 3.2 and USB4 data operation, and a Full-Featured Type‑C receptacle likewise supports the same full set of protocols. It contains a full set of wires and is electronically marked (E-marked): It contains an E-marker chip that responds to the USB Power Delivery Discover Identity command, a kind of vendor-defined message (VDM) sent over the configuration data channel (CC). Using this command, the cable reports its current capacity, maximum speed, and other parameters. Full-Featured USB Type-C devices are a mechanic prerequisite for multi-lane operation (USB 3.2 Gen 1×2, USB 3.2 Gen 2×2, USB4 2×2, USB4 3×2, USB Gen 4 Asymmetric). USB-C devices support power currents of 1.5 A and 3.0 A over the 5 V power bus in addition to baseline 900 mA. These higher currents can be negotiated through the configuration line. Devices can also use the full Power Delivery specification using both BMC-coded configuration line and the legacy BFSK-coded V BUS line.

Standard connectors

Standard‑A connectors: This plug has an elongated rectangular cross-section, inserts into a Standard‑A receptacle on a downstream facing port (DFP) on a USB host or hub, and carries both power and data. The plug itself is 12 mm wide and 4.5 mm thick.* Standard‑B connectors: This plug has a near square cross-section with the top exterior corners beveled. As part of a removable cable, it inserts into a single upstream facing port (UFP) on a device, such as a printer. On some devices, the Standard‑B receptacle has no data connections, being used solely for accepting power from the downstream device. This two-connector-type scheme (A–B) prevents a user from accidentally creating a loop. The maximum allowed cross-section of the overmold boot (which is part of the connector used for its handling) is for the Standard-A plug type, while for the Standard‑B it is .

Micro connectors

Micro-USB connectors, which were announced by the USB-IF on January 4, 2007, have a width similar to that of Mini-USB but approximately half the thickness, enabling their integration into thinner portable devices. The Micro-A plug is with a maximum plug body size of , while the Micro-B plug has the same height and width with a slightly smaller maximum plug body size of . In 2009, several phone manufacturers in europe agreed to standarize on Micro USB for charging, replacing 30 proprietary charging connectors. The thinner Micro-USB connectors were intended to replace the Mini connectors in devices manufactured from May 2007 through late 2014, including smartphones, personal digital assistants, and cameras. plug] The Micro plug design is rated for at least 10,000 connect–disconnect cycles, which is more than the Mini plug design. The Micro connector is also designed to reduce the mechanical wear on the device; instead, the easier-to-replace cable is designed to bear more of the mechanical wear of connection and disconnection. The Universal Serial Bus Micro-USB Cables and Connectors Specification details the mechanical characteristics of Micro-A plugs, Micro-AB receptacles (which accept both Micro-A and Micro-B plugs), and Micro-B plugs and receptacles, along with a permitted adapter with a Standard-A receptacle and a Micro-A plug, as would be used e.g. to connect a camera to an existing Standard-A–B cable attached to a desktop printer. Despite the introduction of the USB-C plug (see below), the Micro-B plug continues to be fitted on certain, often budget, hardware.

OMTP standard

Micro-USB was endorsed as the standard connector for data and power on mobile devices by the cellular phone carrier group Open Mobile Terminal Platform (OMTP) in 2007. Micro-USB was embraced as the "Universal Charging Solution" by the International Telecommunication Union (ITU) in October 2009. In Europe, Micro-USB became the defined common external power supply (EPS) for use with smartphones sold in the EU, and 14 of the world's largest mobile phone manufacturers signed the EU's common EPS Memorandum of Understanding (MoU). Apple, one of the original MoU signers, makes Micro-USB adapters available—as permitted in the Common EPS MoU—for its iPhones equipped with Apple's proprietary 30-pin dock connector and, later, Lightning connector.

Dimensions

Compatibility

Before the specification of the Type‑C plug, virtually every USB cable had one Type‑A plug at one end and one Type‑B plug at the other end of the cable. The Type‑A plug connects only downstream, either directly to a DFP of the host or indirectly, by connecting to a DFP of a hub that itself connects, directly or indirectly, to the host. The Type‑B plug connects only upstream, either directly to the single UFP of a peripheral device or to the UFP of a hub to which further hubs and peripheral devices can be connected. An On-The-Go device has a single Type‑AB port (either Micro‑AB or Mini‑AB) and takes either role according to the plug attached. In a Type‑C–legacy cable, the Type‑C plug is electronically marked to complement the plug at the opposite end: When the legacy plug is a Type‑A, the Type‑C plug is marked as B, and when the legacy plug is a Type‑B, the Type‑C is marked A. A device with a Type‑C receptacle may be capable of taking either role or may only function as one or the other. If a Type‑C plug marked as A or B is connected to a device incapable of taking the necessary role, no communication occurs. When two devices, each capable of taking either role, are connected through a Type‑C–Type‑C cable, there is a negotiation to determine which is the A device and which is the B. Connectors generally support protocols supported by preceding connector types. Remarks: In addition to the above cable assemblies comprising two plugs, receptacles are allowed in three adapter assemblies: Two legacy adapter assemblies for compatibility with equipment that predates USB‑C: USB 3.1 Standard‑A receptacle to Type‑C plug, to connect a legacy Standard‑A plug to a modern Type‑C receptacle USB 2.0 Micro‑B receptacle to Type‑C plug, to connect a legacy Micro‑B plug to a modern Type‑C receptacle One older adapter, itself designated legacy, predating USB‑C: Standard‑A receptacle to Micro‑A plug, giving a compact On-The-Go device, such as a camera or smartphone, a Standard‑A port for connecting peripherals, such as printers and mass storage devices. That is, to connect a Standard‑A plug to a Micro‑AB receptacle. (All USB connectors except Type‑C were designated legacy in 2014. )

Internal connectors

A computer's motherboard includes pin headers for connecting the motherboard to the USB ports on the computer case. The following types are standardized: 9-pin header for two USB 1.1/2.0 Type-A ports. There is also a 5-pin variant for a single port. Motherboards made before 2000 may have other layouts. 19-pin header for two USB 3.0 (also known as 3.1/3.2 Gen 1) Type-A ports. This is not backwards compatible with the 9-pin header; there is no standard for running a newer signal (e.g. Gen 2) over this header, but there is enough signal integrity to do so in practice. "Type-E" ports, which are not pin headers with an array of pins, but a port to plug into: 20-pin Key-A for a single full-featured Type-C, providing up to 80 Gbps in the case of USB4 2.0. (As the original definition is for USB 3.1 Gen 2 [aka USB 3.2 Gen 2, ×2 for two lanes in USB-C], the electrical connection between the case-port and the header may not be of high enough quality for 80 Gbps. USB4 40 Gbps should be achievable as it requires the same cable quality as USB 3.1 Gen 2.) It can also be used to provide one Type-A port up to USB 3.1/3.2 Gen 2. There is officially no provision for providing two Type-A ports from this header as it only provides one pair of legacy (USB 1.1/2.0) data pins. The 20-pin headers are not backwards compatible with either 9 or 19-pin. 20-pin Key-B for two Type-A ports up to USB 3.1/3.2 Gen 2. This header differs from Key-A by reassigning the CC and SBU pins to legacy 1.1/2.0 data (D+, D−) and power (VBUS, GND). Physical keying prevents mixing of Key-A and Key-B port (headers) and plugs. 40-pin, which is functionally the same as two 20-pin Key-A headers put side-by-side. Supports either two Type-C ports, one Type-C plus one Type-A port, or two Type-A ports. A 40-pin port can accept a 20-pin Key-A plug. All these systems are electrically compatible with each other like the USB external connectors are, so passive adapters can be used to mitigate physical incompatibilities, e.g. by converting 19-pin headers to 9-pin headers. It is even possible to convert a 19-pin header to a 20-pin header for USB-C use, albeit without CC and SBU functionality. The shape and contact positions, i.e. footprints, for USB receptables soldered onto circuit boards (surface-mount devices) is partly standardized. In addition, there is an embedded USB (eUSB2) specification describing using USB 2.0 for the communication between two chips on the same circuit board. It uses a lower signaling voltage compared to regular USB 2.0.

Proprietary connectors and formats

Manufacturers of personal electronic devices might not include a USB standard connector on their product for technical or marketing reasons. For example, Olympus has been using a special cable called CB-USB8, one end of which has a special contact. Some manufacturers provide proprietary cables, such as Apple with the Lightning cable, that permit their devices to physically connect to a USB standard port. Full functionality of proprietary ports and cables with USB standard ports is not assured; for example, some devices only use the USB connection for battery charging and do not implement any data transfer functions.

Cabling

. The wires are enclosed in a further layer of shielding. The D± signals used by low, full, and high speed are carried over a twisted pair (typically unshielded) to reduce noise and crosstalk. SuperSpeed uses separate transmit and receive differential pairs, which additionally require shielding (typically, shielded twisted pair but twinax is also mentioned by the specification). Thus, to support SuperSpeed data transmission, cables contain twice as many wires and are larger in diameter. The USB 1.1 standard specifies that a standard cable can have a maximum length of with devices operating at full speed (12 Mbit/s), and a maximum length of with devices operating at low speed (1.5 Mbit/s). USB 2.0 provides for a maximum cable length of for devices running at high speed (480 Mbit/s). The primary reason for this limit is the maximum allowed round-trip delay of about 1.5 μs. If USB host commands are unanswered by the USB device within the allowed time, the host considers the command lost. When adding USB device response time, delays from the maximum number of hubs added to the delays from connecting cables, the maximum acceptable delay per cable amounts to 26 ns. The USB 2.0 specification requires that cable delay be less than ( , ), which is close to the maximum achievable transmission speed for standard copper wire. The USB 3.0 standard does not directly specify a maximum cable length, requiring only that all cables meet an electrical specification: for copper cabling with AWG 26 wires the maximum practical length is . For USB 3.x cables, the D± signals are usually shielded.

Power

Upstream USB connectors supply power at a nominal via the V_BUS pin to downstream USB devices.

USB battery charging

USB Battery Charging (BC) defines a charging port, which may be a charging downstream port (CDP), with data, or a dedicated charging port (DCP), without data. Dedicated charging ports can be found on USB power adapters to run and charge attached devices and charge battery packs. Charging ports on a host with both kinds will be labeled. The charging device identifies a charging port by non-data signaling on the D+ and D− terminals. A dedicated charging port places a resistance not exceeding 200 Ω across the D+ and D− terminals. Per the base specification, any device attached to a standard downstream port (SDP) must initially be a low-power device, with high-power mode contingent on later USB configuration by the host. Charging ports, however, can immediately supply between 0.5 and 1.5 A of current. The charging port must not apply current limiting below 0.5 A, and must not shut down below 1.5 A or before the voltage drops to 2 V. Since these currents are larger than in the original standard, the extra voltage drop in the cable reduces noise margins, causing problems with High Speed signaling. Battery Charging Specification 1.1 specifies that charging devices must dynamically limit bus power current draw during High Speed signaling; 1.2 specifies that charging devices and ports must be designed to tolerate the higher ground voltage difference in High Speed signaling. Revision 1.2 of the specification was released in 20101. It made several changes and increased limits, including allowing 1.5 A on charging downstream ports for unconfigured devices—allowing High Speed communication while having a current up to 1.5 A. Also, support was removed for charging-port detection via resistive mechanisms. Before the Battery Charging Specification was defined, there was no standardized way for the portable device to inquire how much current was available. For example, Apple's iPod and iPhone chargers indicated the available current by voltages on the D− and D+ lines (sometimes also called "Apple Brick ID"): When D+ and D− were both 2.0 V, a device could pull up to 900 mA; When D− was instead 2.8 V, a device could pull up to 1 A; Or else instead if D+ was 2.8 V, a device could pull up to 2 A.

USB Power Delivery

20 Gbps port) In July 2012, the USB Promoters Group announced the finalization of the USB Power Delivery (USB-PD) specification (USB PD rev. 1), an extension that specifies using certified PD aware USB cables with standard USB Type-A and Type-B connectors to deliver increased power (more than the 7.5 W maximum allowed by the previous USB Battery Charging specification) to devices with greater power demands. (USB-PD A and B plugs have a mechanical mark while Micro plugs have a resistor or capacitor attached to the ID pin indicating the cable capability.) USB-PD Devices can request higher currents and supply voltages from compliant hosts—up to 2 A at 5 V (for a power consumption of up to 10 W), and optionally up to 3 A or 5 A at either 12 V (36 W or 60 W) or 20 V (60 W or 100 W). In all cases, both host-to-device and device-to-host configurations are supported. The intent is to permit uniformly charging laptops, tablets, USB-powered disks and similarly higher-power consumer electronics, as a natural extension of existing European and Chinese mobile telephone charging standards. This may also affect the way electric power used for small devices is transmitted and used in both residential and public buildings. The standard is designed to coexist with the previous USB Battery Charging specification. The first Power Delivery specification (Rev. 1.0) defined five fixed power profiles for the power sources. PD-aware devices implement a flexible power management scheme by interfacing with the power source through a bidirectional data channel and requesting a certain level of electrical power, variable up to 5 A and 20 V depending on supported profile. The power configuration protocol can use BMC coding over the configuration channel (CC) wire if one is present, or a 24 MHz BFSK-coded transmission channel on the V BUS line. The USB Power Delivery specification revision 2.0 (USB PD Rev. 2.0) has been released as part of the USB 3.1 suite. It covers the USB-C cable and connector with a separate configuration channel, which now hosts a DC coupled low-frequency BMC-coded data channel that reduces the possibilities for RF interference. Power Delivery protocols have been updated to facilitate USB-C features such as cable ID function, Alternate Mode negotiation, increased V BUS currents, and V CONN -powered accessories. As of specification revision 2.0, version 1.2, the five fixed power profiles for power sources have been deprecated. USB PD Power Rules replace power profiles, defining four normative voltage levels at 5, 9, 15, and 20 V. Instead of five fixed profiles, power supplies may support any maximum source output power from 0.5 W to 100 W. The USB Power Delivery specification revision 3.0 defines an optional Programmable Power Supply (PPS) protocol that allows granular control over V BUS output, allowing a voltage range of 3.3 to 21 V in 20 mV steps, and a current specified in 50 mA steps, to facilitate constant-voltage and constant-current charging. Revision 3.0 also adds extended configuration messages and fast role swap and deprecates the BFSK protocol. PPS can reduce heat generation of both charger and device. On January 8, 2018, USB-IF announced the Certified USB Fast Charger logo for chargers that use the Programmable Power Supply (PPS) protocol from the USB Power Delivery 3.0 specification. In May 2021, the USB PD promoter group launched revision 3.1 of the specification. Revision 3.1 adds Extended Power Range (EPR) mode which allows higher voltages of 28, 36, and 48 V, providing up to 240 W of power (48 V at 5 A), and the "Adjustable Voltage Supply" (AVS) protocol which allows specifying the voltage from a range of 15 to 48 V in 100 mV steps. Higher voltages require electronically marked EPR cables that support 5 A operation and incorporate mechanical improvements required by the USB Type-C standard revision 2.1; existing power modes are retroactively renamed Standard Power Range (SPR). The AVS protocol is not backward compatible with the PPS protocol. A charger that supports AVS may not support PPS as well. In October 2023, the USB PD promoter group launched revision 3.2 of the specification. The AVS protocol now works with the old standard power range (SPR), down to a minimum of 9 V. Prior to Power Delivery, mobile phone vendors used custom protocols to exceed the 7.5 W cap on the USB Battery Charging Specification (BCS). For example, Qualcomm's Quick Charge 2.0 is able to deliver 18 W at a higher voltage, and VOOC delivers 20 W at the normal 5 V. Some of these technologies, such as Quick Charge 4, eventually became compatible with USB PD again. However the maximal power values are barely used in practice, especially for charging of mobile phones: The used standard or used USB-C chargers still remains at 1,5A@5V (=7.5W), which is the same as for USB-A. Only few chargers (sources) and charged devices (phones, clients) can really communicate, and fit the supply/demand combinations, so charging often remains just slow, at the USB-A standard. Some do comply together to use some negotiated PDO (power delivery objects), but their values are static. And because there can be at most only seven PPSs (programmable power supplies), only a few devices can really use the effectiveness of APDOs (Augmented Power Data Object, intervals of values, dynamic by increments of 20/50 mV/mA), usually only two these dynamic offered, leaving five options for some static ones. And even if overheating is prevented, e.g. with 4.1V@2.8A (11.48W), the charging is mostly not even close to the upper power limits of the devices, mostly 27W (9V@3A). That is because the voltages supported by phones are usually 5V or luckily also 9V (3.3-11V on APDO), and 3A at most, often 2.22A only, for voltages over 9V, so 20W is even lower upper limit for power delivery in practice, and still as a peak optimal value. Another reason for differences in speed of charging, the power delivered to mobile phones, are different approaches of producers: E.g. Samsung prefers max charging speed, accepting power even out of USB-C/PPS specifications, so 5A @4.2V (21W) are measurable. On the other hand Sony Xperia shows the very opposite extreme, following strictly the PPS specifications, so when the charging status is out of the official, it quickly defaults down to the basic 1.5A (7W) charging, the "classical slow", effectively protecting the phone from overheating and prolonging lifetime of its battery. Higher powers than 27W/33W are then accomplished by higher current (5A), and higher voltage (20V), which render the upper limit 100W (or 60W @3A). But such high power is not commonly possible for mobile phones, and for currents over 3A special protocols and cables (with electronics inside connectors) are usually needed, e.g. E-marker.

See also

USB-to-serial adapter USB communications

References

Text derived from https://en.wikipedia.org/w/index.php?oldid=1378155157 under CC BY-SA 4.0; modifications have been made.

References

  1. ↩Wikipedia “USB hardware” revision 1378155157 · retrieved 2026-10-20 release date (×1) · confidence 0.95 revision URL