Vibration

Uses your system voice; voice and rate in settings.

Q3556810Snapshot

≈ 20 min read

Names in other languages

  • 中文Vibration广播
  • DeutschVibration
  • EnglishVibration
  • FrançaisVibration
  • Bahasa IndonesiaVibration
  • ItalianoVibration

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

(see other modes) , automotive or mechanical engineering. In mechanics, vibration ( ) is an oscillation of matter about an equilibrium point. Vibration may be deterministic if the oscillations can be characterised precisely (e.g. the periodic motion of a pendulum), or random if the oscillations can only be analysed statistically (e.g. the movement of a tire on a gravel road). Vibration can be desirable: for example, the motion of a tuning fork, the reed in a woodwind instrument or harmonica, a mobile phone, or the cone of a loudspeaker.

In many cases, however, vibration is undesirable, wasting energy and creating unwanted sound. For example, the vibrational motions of engines, electric motors, or any mechanical device in operation are typically unwanted. Such vibrations could be caused by imbalances in the rotating parts, uneven friction, or the meshing of gear teeth. Careful designs usually minimize unwanted vibrations. The studies of sound and vibration are closely related (both fall under acoustics).

How it works

Sound, or pressure waves, are generated by vibrating structures (e.g. vocal cords); these pressure waves can also induce the vibration of structures (e.g. ear drum). Hence, attempts to reduce noise are often related to issues of vibration. Machining vibrations are common in the process of subtractive manufacturing.

(see other modes) , automotive or mechanical engineering. In mechanics, vibration ( ) is an oscillation of matter about an equilibrium point. Vibration may be deterministic if the oscillations can be characterised precisely (e.g. the periodic motion of a pendulum), or random if the oscillations can only be analysed statistically (e.g. the movement of a tire on a gravel road). Vibration can be desirable: for example, the motion of a tuning fork, the reed in a woodwind instrument or harmonica, a mobile phone, or the cone of a loudspeaker.

In many cases, however, vibration is undesirable, wasting energy and creating unwanted sound. For example, the vibrational motions of engines, electric motors, or any mechanical device in operation are typically unwanted. Such vibrations could be caused by imbalances in the rotating parts, uneven friction, or the meshing of gear teeth. Careful designs usually minimize unwanted vibrations. The studies of sound and vibration are closely related (both fall under acoustics).

Sound, or pressure waves, are generated by vibrating structures (e.g. vocal cords); these pressure waves can also induce the vibration of structures (e.g. ear drum). Hence, attempts to reduce noise are often related to issues of vibration. Machining vibrations are common in the process of subtractive manufacturing. F_s=- k x. \! The force generated by the mass is proportional to the acceleration of the mass as given by Newton's second law of motion: \Sigma\ F = ma = m \ddot{x} = m \frac{d^2x}{dt^2}.

The sum of the forces on the mass then generates this ordinary differential equation: \ m \ddot{x} + k x = 0. Assuming that the initiation of vibration begins by stretching the spring by the distance of A and releasing, the solution to the above equation that describes the motion of mass is: x(t) = A \cos (2 \pi f_n t). \! This solution says that it will oscillate with simple harmonic motion that has an amplitude of A and a frequency of f n . The number f n is called the undamped natural frequency.

For the simple mass–spring system, f n is defined as: f_n = {1\over {2 \pi}} \sqrt{k \over m}. \! Note: angular frequency ω (ω=2 π f) with the units of radians per second is often used in equations because it simplifies the equations, but is normally converted to ordinary frequency (units of Hz or equivalently cycles per second) when stating the frequency of a system. If the mass and stiffness of the system is known, the formula above can determine the frequency at which the system vibrates once set in motion by an initial disturbance.

Every vibrating system has one or more natural frequencies that it vibrates at once disturbed. This simple relation can be used to understand in general what happens to a more complex system once we add mass or stiffness. For example, the above formula explains why, when a car or truck is fully loaded, the suspension feels "softer" than unloaded—the mass has increased, reducing the natural frequency of the system. F_\text{d} = - c v = - c \dot{x} = - c \frac{dx}{dt}.

Summing the forces on the mass results in the following ordinary differential equation: m \ddot{x} + c \dot{x} + kx = 0. The solution to this equation depends on the amount of damping. If the damping is small enough, the system still vibrates—but eventually, over time, stops vibrating. This case is called underdamping, which is important in vibration analysis. If damping is increased just to the point where the system no longer oscillates, the system has reached the point of critical damping.

If the damping is increased past critical damping, the system is overdamped. The value that the damping coefficient must reach for critical damping in the mass-spring-damper model is: c_\text{c} = 2 \sqrt{km} The damping ratio is used to characterize the amount of damping in a system. This is a ratio of the actual damping over the amount of damping required to reach critical damping. The formula for the damping ratio ( \zeta ) of the mass-spring-damper model is: \zeta = { c \over 2 \sqrt{km} }.

For example, metal structures (e.g., airplane fuselages, engine crankshafts) have damping factors less than 0.05, while automotive suspensions are in the range of 0.2–0.3. The solution to the underdamped system for the mass-spring-damper model is the following: x(t)=X e^{-\zeta \omega_n t} \cos\left( \sqrt{1-\zeta^2} \omega_n t - \phi \right) , \qquad \omega_n = 2\pi f_n. The value of X, the initial magnitude, and \phi, the phase shift, are determined by the amount the spring is stretched.

The formulas for these values can be found in the references. f_\text{d}= f_n\sqrt{1-\zeta^2}. The damped natural frequency is less than the undamped natural frequency, but for many practical cases the damping ratio is relatively small and hence the difference is negligible. Therefore, the damped and undamped description are often dropped when stating the natural frequency (e.g. with 0.1 damping ratio, the damped natural frequency is only 1% less than the undamped).

Impact

The plots to the side present how 0.1 and 0.3 damping ratios affect how the system "rings" down over time. What is often done in practice is to experimentally measure the free vibration after an impact (for example by a hammer) and then determine the natural frequency of the system by measuring the rate of oscillation, as well as the damping ratio by measuring the rate of decay. The natural frequency and damping ratio are not only important in free vibration, but also characterize how a system behaves under forced vibration.

Both the damped and undamped natural frequencies can be estimate when the mode shapes are not known using the Rayleigh Quotient. F= F_0 \sin(2 \pi f t). \! Summing the forces on the mass results in the following ordinary differential equation: m \ddot{x} + c\dot{x} + k x = F_0 \sin(2 \pi f t). The steady state solution of this problem can be written as: x(t)= X \sin(2 \pi f t +\phi). \! The result states that the mass will oscillate at the same frequency, f, of the applied force, but with a phase shift \phi.

The amplitude of the vibration “X” is defined by the following formula. X= {F_0 \over k} {1 \over \sqrt{(1-r^2)^2 + (2 \zeta r)^2}}. Where “r” is defined as the ratio of the harmonic force frequency over the undamped natural frequency of the mass–spring–damper model. r=\frac{f}{f_n}. The phase shift, \phi, is defined by the following formula. \phi= \arctan\left (\frac{-2 \zeta r}{1-r^2} \right). The plot of these functions, called "the frequency response of the system", presents one of the most important features in forced vibration.

In a lightly damped system when the forcing frequency nears the natural frequency ( r \approx 1 ) the amplitude of the vibration can get extremely high. This phenomenon is called resonance (subsequently the natural frequency of a system is often referred to as the resonant frequency). In rotor bearing systems any rotational speed that excites a resonant frequency is referred to as a critical speed. If resonance occurs in a mechanical system it can be very harmful – leading to eventual failure of the system.

Consequently, one of the major reasons for vibration analysis is to predict when this type of resonance may occur and then to determine what steps to take to prevent it from occurring. As the amplitude plot shows, adding damping can significantly reduce the magnitude of the vibration. Also, the magnitude can be reduced if the natural frequency can be shifted away from the forcing frequency by changing the stiffness or mass of the system.

If the system cannot be changed, perhaps the forcing frequency can be shifted (for example, changing the speed of the machine generating the force). The following are some other points in regards to the forced vibration shown in the frequency response plots.

At a given frequency ratio, the amplitude of the vibration, X, is directly proportional to the amplitude of the force F_0 (e.g. if you double the force, the vibration doubles) With little or no damping, the vibration is in phase with the forcing frequency when the frequency ratio r   1 When r ≪ 1 the amplitude is just the deflection of the spring under the static force F_0. This deflection is called the static deflection \delta_{st}. Hence, when r ≪ 1 the effects of the damper and the mass are minimal.

When r ≫ 1 the amplitude of the vibration is actually less than the static deflection \delta_{st}. In this region the force generated by the mass (F = ma) is dominating because the acceleration seen by the mass increases with the frequency. Since the deflection seen in the spring, X, is reduced in this region, the force transmitted by the spring (F = kx) to the base is reduced. Therefore, the mass–spring–damper system is isolating the harmonic force from the mounting base – referred to as vibration isolation.

More damping actually reduces the effects of vibration isolation when r ≫ 1 because the damping force (F = cv) is also transmitted to the base. Whatever the damping is, the vibration is 90 degrees out of phase with the forcing frequency when the frequency ratio r = 1, which is very helpful when it comes to determining the natural frequency of the system.

Whatever the damping is, when r ≫ 1, the vibration is 180 degrees out of phase with the forcing frequency Whatever the damping is, when r ≪ 1, the vibration is in phase with the forcing frequency X(i\omega)=H(i\omega)\cdot F(i\omega) \text{ or } H(i\omega)= {X(i\omega) \over F(i\omega)}. H(i\omega) is called the frequency response function (also referred to as the transfer function, but not technically as accurate) and has both a magnitude and phase component (if represented as a complex number, a real and imaginary component).

The magnitude of the frequency response function (FRF) was presented earlier for the mass–spring–damper system. |H(i\omega)|=\left |{X(i\omega) \over F(i\omega)} \right|= {1 \over k} {1 \over \sqrt{(1-r^2)^2 + (2 \zeta r)^2}}, \text{ where } r=\frac{f}{f_n}=\frac{\omega}{\omega_n}. The phase of the FRF was also presented earlier as: \angle H(i\omega)= -\arctan\left (\frac{2 \zeta r}{1-r^2} \right). For example, calculating the FRF for a mass–spring–damper system with a mass of 1 kg, spring stiffness of 1.93 N/mm and a damping ratio of 0.1.

The values of the spring and mass give a natural frequency of 7 Hz for this specific system. Applying the 1 Hz square wave from earlier allows the calculation of the predicted vibration of the mass. The figure illustrates the resulting vibration. It happens in this example that the fourth harmonic of the square wave falls at 7 Hz. The frequency response of the mass–spring–damper therefore outputs a high 7 Hz vibration even though the input force had a relatively low 7 Hz harmonic.

Evidence and sources

This example highlights that the resulting vibration is dependent on both the forcing function and the system that the force is applied to. The figure also shows the time domain representation of the resulting vibration. This is done by performing an inverse Fourier Transform that converts frequency domain data to time domain. In practice, this is rarely done because the frequency spectrum provides all the necessary information.

The frequency response function (FRF) does not necessarily have to be calculated from the knowledge of the mass, damping, and stiffness of the system—but can be measured experimentally. For example, if a known force over a range of frequencies is applied, and if the associated vibrations are measured, the frequency response function can be calculated, thereby characterizing the system.

This technique is used in the field of experimental modal analysis to determine the vibration characteristics of a structure. m_1 \ddot{x_1} + (c_1+c_2) \dot{x_1} - c_2 \dot{x_2}+ (k_1+k_2) x_1 - k_2 x_2= f_1, m_2 \ddot{x_2} - c_2 \dot{x_1}+ (c_2+c_3) \dot{x_2} - k_2 x_1+ (k_2+k_3) x_2 = f_2. \!

This can be rewritten in matrix format: \begin{bmatrix}m_1 & 0\\ 0 & m_2\end{bmatrix}\begin{Bmatrix}\ddot{x_1}\\ \ddot{x_2} \end{Bmatrix} + \begin{bmatrix} c_1+c_2 & -c_2\\ -c_2 & c_2+c_3\end{bmatrix}\begin{Bmatrix}\dot{x_1}\\ \dot{x_2}\end{Bmatrix}+\begin{bmatrix}k_1+k_2 & -k_2\\ -k_2 & k_2+k_3\end{bmatrix}\begin{Bmatrix} x_1\\ x_2\end{Bmatrix}=\begin{Bmatrix} f_1\\ f_2\end{Bmatrix}.

A more compact form of this matrix equation can be written as: \begin{bmatrix}M\end{bmatrix}\begin{Bmatrix}\ddot{x}\end{Bmatrix}+\begin{bmatrix}C\end{bmatrix}\begin{Bmatrix}\dot{x}\end{Bmatrix}+\begin{bmatrix}K\end{bmatrix}\begin{Bmatrix} x\end{Bmatrix}=\begin{Bmatrix} f \end{Bmatrix} where \begin{bmatrix}M\end{bmatrix}, \begin{bmatrix}C\end{bmatrix}, and \begin{bmatrix}K\end{bmatrix} are symmetric matrices referred respectively as the mass, damping, and stiffness matrices.

The matrices are NxN square matrices where N is the number of degrees of freedom of the system. The following analysis involves the case where there is no damping and no applied forces (i.e. free vibration). The solution of a viscously damped system is somewhat more complicated. \begin{bmatrix}M\end{bmatrix}\begin{Bmatrix}\ddot{x}\end{Bmatrix}+\begin{bmatrix}K\end{bmatrix}\begin{Bmatrix} x\end{Bmatrix}=0.

This differential equation can be solved by assuming the following type of solution: \begin{Bmatrix} x\end{Bmatrix}=\begin{Bmatrix} X\end{Bmatrix}e^{i\omega t}. Note: Using the exponential solution of \begin{Bmatrix} X\end{Bmatrix}e^{i\omega t} is a mathematical trick used to solve linear differential equations. Using Euler's formula and taking only the real part of the solution it is the same cosine solution for the 1 DOF system. The exponential solution is only used because it is easier to manipulate mathematically.

The equation then becomes: \begin{bmatrix}-\omega^2 \begin{bmatrix} M \end{bmatrix} + \begin{bmatrix} K \end{bmatrix} \end{bmatrix} \begin{Bmatrix}X\end{Bmatrix}e^{i\omega t}=0.

Since e^{i\omega t} cannot equal zero the equation reduces to the following. \begin{bmatrix}\begin{bmatrix}K\end{bmatrix}-\omega^2 \begin{bmatrix} M \end{bmatrix} \end{bmatrix} \begin{Bmatrix} X \end{Bmatrix}=0. \begin{bmatrix}\begin{bmatrix}M\end{bmatrix}^{-1}\begin{bmatrix}K\end{bmatrix}-\omega^2 \begin{bmatrix} M \end{bmatrix}^{-1} \begin{bmatrix}M\end{bmatrix}\end{bmatrix}\begin{Bmatrix}X\end{Bmatrix}=0 and if: \begin{bmatrix}M\end{bmatrix}^{-1}\begin{bmatrix}K\end{bmatrix}=\begin{bmatrix}A\end{bmatrix} and \lambda=\omega^2 \, \begin{bmatrix}\begin{bmatrix}A\end{bmatrix}-\lambda\begin{bmatrix}I\end{bmatrix}\end{bmatrix}\begin{Bmatrix}X\end{Bmatrix}=0.

The solution to the problem results in N eigenvalues (i.e. \omega_1^2,\omega_2^2,\cdots\omega_N^2 ), where N corresponds to the number of degrees of freedom. The eigenvalues provide the natural frequencies of the system. When these eigenvalues are substituted back into the original set of equations, the values of \begin{Bmatrix}X\end{Bmatrix} that correspond to each eigenvalue are called the eigenvectors. These eigenvectors represent the mode shapes of the system.

The solution of an eigenvalue problem can be quite cumbersome (especially for problems with many degrees of freedom), but fortunately most math analysis programs have eigenvalue routines.

The eigenvalues and eigenvectors are often written in the following matrix format and describe the modal model of the system: \begin{bmatrix}^\diagdown \omega_{r\diagdown}^2 \end{bmatrix}=\begin{bmatrix} \omega_1^2 & \cdots & 0 \\ \vdots & \ddots & \vdots \\ 0 & \cdots & \omega_N^2 \end{bmatrix} \text{ and } \begin{bmatrix} \Psi \end{bmatrix}=\begin{bmatrix} \begin{Bmatrix} \psi_1 \end{Bmatrix} \begin{Bmatrix} \psi_2 \end{Bmatrix} \cdots \begin{Bmatrix} \psi_N \end{Bmatrix} \end{bmatrix}.

A simple example using the 2 DOF model can help illustrate the concepts. Let both masses have a mass of 1 kg and the stiffness of all three springs equal 1000 N/m. The mass and stiffness matrix for this problem are then: \begin{bmatrix}M\end{bmatrix}=\begin{bmatrix}1 & 0\\ 0 & 1\end{bmatrix} and \begin{bmatrix}K\end{bmatrix}=\begin{bmatrix}2000 & -1000\\ -1000 & 2000\end{bmatrix}. Then \begin{bmatrix}A\end{bmatrix}=\begin{bmatrix}2000 & -1000\\ -1000 & 2000\end{bmatrix}.

The eigenvalues for this problem given by an eigenvalue routine is: \begin{bmatrix} ^\diagdown \omega_{r\diagdown}^2 \end{bmatrix}=\begin{bmatrix} 1000 & 0 \\ 0 & 3000 \end{bmatrix}. The natural frequencies in the units of hertz are then (remembering \scriptstyle \omega=2 \pi f ) \scriptstyle f_1=5.033 \mathrm {\ Hz} and \scriptstyle f_2=8.717 \text{ Hz}.

The two mode shapes for the respective natural frequencies are given as: \begin{bmatrix} \Psi \end{bmatrix}=\begin{bmatrix} \begin{Bmatrix} \psi_1 \end{Bmatrix} \begin{Bmatrix} \psi_2 \end{Bmatrix} \end{bmatrix}= \begin{bmatrix} \begin{Bmatrix} -0.707 \\ -0.707 \end{Bmatrix}_1 \begin{Bmatrix} 0.707 \\ -0.707 \end{Bmatrix}_2 \end{bmatrix}. Since the system is a 2 DOF system, there are two modes with their respective natural frequencies and shapes.

The mode shape vectors are not the absolute motion, but just describe relative motion of the degrees of freedom. In our case the first mode shape vector is saying that the masses are moving together in phase since they have the same value and sign.

In the case of the second mode shape vector, each mass is moving in opposite direction at the same rate. \begin{bmatrix}\Psi\end{bmatrix}^{T}\begin{bmatrix}M\end{bmatrix}\begin{bmatrix}\Psi\end{bmatrix}=\begin{bmatrix} ^\diagdown m_{r\diagdown} \end{bmatrix}, \begin{bmatrix}\Psi\end{bmatrix}^{T}\begin{bmatrix}K\end{bmatrix}\begin{bmatrix}\Psi\end{bmatrix}=\begin{bmatrix} ^\diagdown k_{r\diagdown} \end{bmatrix}. \begin{bmatrix} ^\diagdown m_{r\diagdown} \end{bmatrix} and \begin{bmatrix} ^\diagdown k_{r\diagdown} \end{bmatrix} are diagonal matrices that contain the modal mass and stiffness values for each one of the modes.

(Note: Since the eigenvectors (mode shapes) can be arbitrarily scaled, the orthogonality properties are often used to scale the eigenvectors so the modal mass value for each mode is equal to 1. The modal mass matrix is therefore an identity matrix) These properties can be used to greatly simplify the solution of multi-degree of freedom models by making the following coordinate transformation. \begin{Bmatrix} x \end{Bmatrix}= \begin{bmatrix} \Psi \end{bmatrix} \begin{Bmatrix} q \end{Bmatrix}.

Using this coordinate transformation in the original free vibration differential equation results in the following equation. \begin{bmatrix}M\end{bmatrix}\begin{bmatrix} \Psi \end{bmatrix} \begin{Bmatrix} \ddot{q} \end{Bmatrix} + \begin{bmatrix} K \end{bmatrix} \begin{bmatrix} \Psi \end{bmatrix} \begin{Bmatrix} q\end{Bmatrix}=0.

Taking advantage of the orthogonality properties by premultiplying this equation by \begin{bmatrix}\Psi\end{bmatrix}^{T} \begin{bmatrix}\Psi\end{bmatrix}^{T}\begin{bmatrix}M\end{bmatrix}\begin{bmatrix} \Psi \end{bmatrix}\begin{Bmatrix}\ddot{q}\end{Bmatrix}+\begin{bmatrix}\Psi\end{bmatrix}^{T}\begin{bmatrix}K\end{bmatrix} \begin{bmatrix} \Psi \end{bmatrix} \begin{Bmatrix} q\end{Bmatrix}=0.

The orthogonality properties then simplify this equation to: \begin{bmatrix} ^\diagdown m_{r\diagdown} \end{bmatrix} \begin{Bmatrix}\ddot{q}\end{Bmatrix}+\begin{bmatrix}^\diagdown k_{r\diagdown}\end{bmatrix} \begin{Bmatrix} q\end{Bmatrix}=0. This equation is the foundation of vibration analysis for multiple degree of freedom systems. A similar type of result can be derived for damped systems. The key is that the modal mass and stiffness matrices are diagonal matrices and therefore the equations have been "decoupled".

In other words, the problem has been transformed from a large unwieldy multiple degree of freedom problem into many single degree of freedom problems that can be solved using the same methods outlined above. Solving for x is replaced by solving for q, referred to as the modal coordinates or modal participation factors.

It may be clearer to understand if \begin{Bmatrix} x \end{Bmatrix}= \begin{bmatrix} \Psi \end{bmatrix} \begin{Bmatrix} q \end{Bmatrix} is written as: \begin{Bmatrix} x_n \end{Bmatrix}= q_1\begin{Bmatrix} \psi \end{Bmatrix}_1 +q_2\begin{Bmatrix} \psi \end{Bmatrix}_2 +q_3\begin{Bmatrix} \psi \end{Bmatrix}_3 +\cdots + q_N\begin{Bmatrix} \psi \end{Bmatrix}_N. Written in this form it can be seen that the vibration at each of the degrees of freedom is just a linear sum of the mode shapes.

Furthermore, how much each mode "participates" in the final vibration is defined by q, its modal participation factor. Vibration Analysis Reference – Mobius Institute Condition Monitoring and Machinery Protection – Siemens AG

Text derived from https://en.wikipedia.org/w/index.php?oldid=1375046202 under CC BY-SA 4.0; modifications have been made.

Provenance

snapshot vibration-410397-5ef63666f04cabe9 · hash 5ef63666f04cabe98080284a6ea8b070afb0d0790004e8b2c4d23bb94f561828 · captured 1789477126.0 · version history

Cite this page as: encyclopegia.org, “Vibration”, snapshot vibration-410397-5ef63666f04cabe9. https://encyclopegia.org/a/vibration

Sources cited in this revision

5 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.