Wafer (electronics)

In electronics, a wafer (also called a slice or substrate) is a thin slice of semiconductor, such as a crystalline silicon (c-Si, silicium), used for the fabrication of integrated circuits and, in photovoltaics, to manufacture solar cells.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 3 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In electronics, a wafer (also called a slice or substrate) is a thin slice of semiconductor, such as a crystalline silicon (c-Si, silicium), used for the fabrication of integrated circuits and, in photovoltaics, to manufacture solar cells. The wafer serves as the substrate for microelectronic devices built in and upon the wafer.

It undergoes many microfabrication processes, such as doping, ion implantation, etching, thin-film deposition of various materials, and photolithographic patterning. Finally, the individual microcircuits are separated by wafer dicing and packaged as an integrated circuit.

450 mm wafers

DPW = \left\lfloor\frac{\pi r^2}{S}\right\rfloor = \left\lfloor\frac{\pi d^2}{4S}\right\rfloor , where d is the wafer diameter (typically in mm) S the size of each die (mm 2 ) including the width of the scribeline ( or in the case of a saw lane, the kerf plus a tolerance). This formula simply states that the number of dies which can fit on the wafer cannot exceed the area of the wafer divided by the area of each individual die.

It will always overestimate the true best-case gross DPW, since it includes the area of partially patterned dies which do not fully lie on the wafer surface (see figure). These partially patterned dies don't represent complete ICs, so they usually cannot be sold as functional parts.

Refinements of this simple formula typically add an edge correction, to account for partial dies on the edge, which in general will be more significant when the area of the die is large compared to the total area of the wafer. In the other limiting case (infinitesimally small dies or infinitely large wafers), the edge correction is negligible.

The correction factor or correction term generally takes one of the forms cited by De Vries: DPW = \frac{\displaystyle \pi d^2}{4S} - \frac{\displaystyle \pi d}{\sqrt{2S}} (area ratio – circumference/(die diagonal length)) or DPW = \left(\frac{\displaystyle \pi d^2}{4S}\right) \exp(-2 \sqrt{S}/d) (area ratio scaled by an exponential factor) or DPW = \frac{\displaystyle \pi d^2}{4S} \left(1 - \frac{\displaystyle 2\sqrt{S}}{d} \right)^2 (area ratio scaled by a polynomial factor). Studies comparing these analytical formulas to brute-force computational results show that the formulas can be made more accurate, over practical ranges of die sizes and aspect ratios, by adjusting the coefficients of the corrections to values above or below unity, and by replacing the linear die dimension \sqrt{S} with (H+W)/2 (average side length) in the case of dies with large aspect ratio: DPW = \frac{\displaystyle \pi d^2}{4S} - 0.58^{*} \frac{\displaystyle \pi d}{\sqrt{S}} or DPW = \left(\frac{\displaystyle \pi d^2}{4S}\right) \exp(-2.32^{*} \sqrt{S}/d) or DPW = \frac{\displaystyle \pi d^2}{4S} \left(1 - \frac{\displaystyle 1.16^{*} \sqrt{S}}{d} \right)^2 .

Text derived from https://en.wikipedia.org/w/index.php?oldid=1377610872 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

33 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.