Washer (hardware)
A washer is a thin plate (typically disk-shaped, but sometimes square) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such as a bolt or nut.
≈ 6 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
A washer is a thin plate (typically disk-shaped, but sometimes square) with a hole (typically in the middle) that is normally used to distribute the load of a threaded fastener, such as a bolt or nut. Other uses of washers are as a spacer, spring (Belleville washer, wave washer), wear pad, preload indicating device, locking device, and to reduce vibration (rubber washer).
Washers are usually metal or plastic. High-quality bolted joints require hardened steel washers to prevent the loss of pre-load due to brinelling after the torque is applied. Washers are also important for preventing galvanic corrosion, particularly by insulating steel screws from aluminium surfaces.
They may also be used in rotating devices, as a bearing. A thrust washer is used when a rolling element bearing is not needed either from a cost-performance perspective or due to space restraints. Coatings can be used to reduce wear and friction, either by hardening the surface or by providing a solid lubricant (i.e. a self-lubricating surface).
Rubber or fiber gaskets used in taps (or faucets, valves, and other piping connections) as seal against water leaks are sometimes referred to colloquially as washers; but, while they may look similar, washers and gaskets are usually designed for different functions and made differently.
Etymology
The origin of the word is unknown. The first recorded use of the word was in 1346; however, the first time its definition was recorded was in 1611.
Washer types
Most washers can be categorized into three broad types; Plain washers, which spread a load, and prevent damage to the adjacent surface, or which provide some sort of insulation (such as electrical insulation) Spring washers, which have axial flexibility and are used to prevent fastening or loosening due to vibrations Locking washers, which prevent fastening or loosening by preventing unscrewing rotation of the fastening device; locking washers are usually also spring washers.
Spring and locking washers
Lock washers, locknuts, jam nuts, and thread-locking fluid are ways to prevent vibration from loosening a bolted joint.
Gaskets
The term washer is often applied to various gasket types such as those used to seal the control valve in taps.
Specialised types
The DIN 125 metric washer standard refers to subtypes A and B. ISO 7089 calls these Form A and ISO 7090 calls them Form B. They are all the same overall size, but Form B is chamfered on one side.
Materials
Washers can be fabricated from a variety of materials including, but not limited to: Steel – Carbon steel, spring steel, A2 (304) stainless steel, and A4 (316/316L) stainless steel Non-ferrous metal – Copper, brass, aluminium, titanium, iron, bronze, and zinc Alloy – Silicon bronze, Inconel, Monel, and Hastelloy Plastic – Thermoplastics and thermosetting polymers such as polyethylene, PTFE (Teflon) Nylon – Nylon 6, Nylon 66, Nylatron, and Tecamid MDS Specialty – Fibers, ceramics, rubber, felt, leather, bimetals, and mica Phenolic – The material has good electrical insulation, is lightweight, tough, has low moisture absorption, is heat resistant, and is resistant to chemicals and corrosion. Phenolic washers are substitutes for flat metallic washers in cases where electrical insulation is required.
Phenolic washers are stamped out of large sheets of the phenolic material. The term "phenolic washer" is sometimes used for stamped washers from laminated materials such as paper, canvas, and Mylar.
Type and form
The American National Standards Institute (ANSI) provides standards for general use flat washers. Type A is a series of steel washers at broad tolerances, where precision is not critical. Type B is a series of flat washers with tighter tolerances where outside diameters are categorized as "narrow", "regular" or "wide" for specific bolt sizes.
"Type" is not to be confused with "form" (but often is). The British Standard for Metric Series Metal Washers (BS4320), written in 1968, coined the term "form". The forms go from A to G and dictate the outside diameter and thickness of the flat washers.
Form A: Normal diameter, normal thickness Form B: Normal diameter, light thickness Form C: Large diameter, normal thickness Form D: Large diameter, light thickness Form E: Normal diameter, normal thickness Form F: Large diameter, normal thickness Form G: Largest diameter, larger thickness. Washer 'form' when comparing different washer material types is used quite freely by stockists.
In relation to BS4320 specifically, washer forms 'A' to 'D' inclusive are designated 'bright metal' washers and are supplied self-finished in various metals including: steel alloys, brass, copper, etc. Whereas, BS4320 washer forms 'E' to 'G' inclusive are designated 'black' (uncoated) mild steel washers, which normally are specified with a supplementary protective coating supply condition.
See also
Bit guard Dowel Unified Thread Standard
Further reading
Parmley, Robert. (2000). "Section 11: Washers."
Illustrated Sourcebook of Mechanical Components. New York: McGraw Hill. Drawings, designs and discussion of various uses of washers.
External links
(http://www.fastenerdata.co.uk/flat-washers Dimensions of Global washers ASME Plain washer dimensions (Type A and Type B) Typical USA Flat Washer Dimensions USS, SAE, Fender, and NAS washer ID & OD (mm) American National Standard (ANSI) Type B Plain Washers SAE Flat Washers Type A Plain Washers USS & SAE Combined Flat Washer Dimensions Flat Washer Thickness Table Steel Gage Thicknesses, non-metric Split Lockwashers: Truth vs. Myth Hill Country Engineering Using machine washers Machine Design - Using washers
Text derived from https://en.wikipedia.org/w/index.php?oldid=1377707496 under CC BY-SA 4.0; modifications have been made.