Water injection (engine)
In internal combustion engines, water injection, also known as anti-detonant injection (ADI), can spray water into the incoming air or air–fuel mixture, or directly into the combustion chamber to cool certain parts of the induction system…
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
In internal combustion engines, water injection, also known as anti-detonant injection (ADI), can spray water into the incoming air or air–fuel mixture, or directly into the combustion chamber to cool certain parts of the induction system where "hot points" could produce premature ignition. In jet engines—particularly early turbojets or engines in which it is not practical or desirable to have an afterburner—water injection may be used to increase engine thrust, particularly at low altitudes and at takeoff.
Water injection was used historically to increase the power output of military aviation engines for short durations, such as during aerial combat or takeoff. It has also been used in motor sports and notably in drag racing.
In Otto cycle engines, the cooling effect of water injection enables greater compression ratios by reducing engine knocking (detonation), which allows significant performance gains when used in conjunction with a supercharger, turbocharger, or modifications such as aggressive ignition timing. Depending on the engine, improvements in power and fuel efficiency can also be obtained solely by injecting water.
Water injection may also be used to reduce or carbon monoxide emissions.
Composition of fluid
Many water injection systems use a mixture of water and alcohol (often close to 50-50), with trace amounts of water-miscible oil. The high heat capacity of water provides the primary cooling effect. The alcohol is combustible and also serves as an antifreeze for the water. The main purpose of the oil is to prevent corrosion of water injection and fuel system components.
Use in aircraft
with J57 engines]] with BMW 801 engine getting up to extra from water injection mixture]] aircraft engine at the BMW Museum]] Water injection has been used in both reciprocating and turbine aircraft engines. In a reciprocating engine, the use of water injection, also called anti-detonation injection or ADI, is used to prevent engine knocking also known as "detonation".
Commonly found on large radial engines with pressure carburetors, it is a mixture of water and alcohol injected into the carburetor at high power settings. When using a rich mixture, the engine runs cooler but cannot reach maximum power, and a leaner mixture means detonation is likely.
With the use of ADI, the injected water and alcohol absorb the excess heat to prevent detonation while still allowing for a leaner and more powerful mixture. Notable engines with water fuel injection include BMW 801, Daimler-Benz DB 605, Junkers Jumo 213, Pratt & Whitney R-2800 Double Wasp.
When used in a turbine engine, the effects are similar, except that preventing detonation is normally not the primary goal. Water is normally injected either at the compressor inlet or in the diffuser just before the combustion chamber. Adding water increases the mass being accelerated out of the engine, increasing thrust; and it also serves to cool the turbines.
Since temperature is normally the limiting factor in turbine engine performance at low altitudes, the cooling effect lets the engine run at higher RPM with more fuel injected and more thrust created without overheating. Prior to the widespread adoption of afterburning engines, some first-generation jet fighters used water injection to provide a moderate boost in performance.
For example, the late-model variant of the Lockheed F-80 Shooting Star, the F-80C, used water injection on its Allison J33-A-35 engine. Water injection increased thrust from , a 17% thrust increase (at sea level).
Early versions of the Boeing 707 fitted with Pratt & Whitney JT3C turbojets used water injection for extra takeoff power, as did Boeing 747-100 and 200 aircraft fitted with Pratt & Whitney JT9D-3AW and -7AW turbofans; this system was not included in later versions fitted with more powerful engines. The BAC One-Eleven airliner used water injection for its Rolls-Royce Spey turbofan engines.
Filling the tanks with jet fuel instead of water led to the 1971 Paninternational Flight 112 crash. In 1978, Olympic Airways Flight 411 had to abort and return to its take-off airport due to a failure of the water injection system or its processes.
Use in automobiles
A limited number of road vehicles with forced induction engines from manufacturers such as Chrysler have included water injection. The 1962 Oldsmobile Jetfire was delivered with the Turbo Jetfire engine.
Use in diesel
A 2016 study combined water injection with exhaust gas recirculation. Water was injected into the exhaust manifold of a diesel engine and, by opening the exhaust valve during the induction stroke, the injected water and some of the exhaust gas was drawn back into the cylinder. The effect was up to 85% reduction in emissions and also significant reduction in soot emissions.
See also
Crower six stroke
Text derived from https://en.wikipedia.org/w/index.php?oldid=1364508621 under CC BY-SA 4.0; modifications have been made.