{
  "id": "enwiki-001350834674",
  "slug": "wire-wrap",
  "title": "Wire wrap",
  "qid": "",
  "lead": "of wire-wrap connections telephone crossbar switch. Some types of connection were soldered. Wire wrap is an electronic component assembly technique that was invented to wire telephone crossbar switches, and later adapted to construct electronic circuit boards. Electronic components mounted on an insulating board are interconnected by lengths of insulated wire run between their terminals, with the connections made by wrapping several turns of uninsulated sections of the wire around a component lead or a socket pin. Wires can be wrapped by hand or by machine, and can be hand-modified afterwards. It was popular for large-scale manufacturing in the 1960s and early 1970s, and continues today to be used for short runs and prototypes. The method eliminates the design and fabrication of a printed circuit board. Wire wrapping is unusual among other prototyping technologies since it allows for complex assemblies to be produced by automated equipment, but then easily repaired or modified by hand. Wire wrap was used for assembly of high frequency prototypes and small production runs, including gigahertz microwave circuits and supercomputers. It is unique among automated prototyping techniques in that wire lengths can be exactly controlled, and twisted pairs or magnetically shielded twisted quads can be routed together.…",
  "body": "of wire-wrap connections telephone crossbar switch. Some types of connection were soldered. Wire wrap is an electronic component assembly technique that was invented to wire telephone crossbar switches, and later adapted to construct electronic circuit boards. Electronic components mounted on an insulating board are interconnected by lengths of insulated wire run between their terminals, with the connections made by wrapping several turns of uninsulated sections of the wire around a component lead or a socket pin. Wires can be wrapped by hand or by machine, and can be hand-modified afterwards. It was popular for large-scale manufacturing in the 1960s and early 1970s, and continues today to be used for short runs and prototypes. The method eliminates the design and fabrication of a printed circuit board. Wire wrapping is unusual among other prototyping technologies since it allows for complex assemblies to be produced by automated equipment, but then easily repaired or modified by hand. Wire wrap was used for assembly of high frequency prototypes and small production runs, including gigahertz microwave circuits and supercomputers. It is unique among automated prototyping techniques in that wire lengths can be exactly controlled, and twisted pairs or magnetically shielded twisted quads can be routed together. Wire wrap construction became popular around 1960 in circuit board manufacturing, and use has now sharply declined. Surface-mount technology has made the technique comparatively much less useful than in previous decades. Solder-less breadboards and the decreasing cost of professionally made PCBs have nearly eliminated this technology. The earliest machines (14FB and 14FG models, for example) were initially configured as \"horizontal\", which meant that the wire wrap board was placed upside down (pins up) onto a horizontal tooling plate, which was then rolled into the machine and locked onto a rotating (TRP table rotational position of four positions) and shifting (PLP = pallet longitudinal position of 11 positions) pallet assembly. These machines included very large hydraulic units for powering the servos that drove the ball screw mounted \"A\" and \"B\" drive carriages, a tall electronics cabinet loaded with hundreds of IBM control relays, many dozens of solenoids for controlling the various pneumatic mechanical subsystems, and an IBM 029 card reader for positioning instructions. The automatic wire wrap machines themselves were quite large, tall and square. Servicing the machines was extremely complex, and often meant climbing inside them just to work on them. This could be quite dangerous if safety interlocks were not maintained properly. Later, somewhat smaller machines were \"vertical\" (14FV) which meant the boards were placed onto a tooling plate with pins facing the machine operator. Gone were the hydraulic units, in favor of direct drive motors to rotate the ball screws, with rotary encoders to provide positioning feedback. This generally provided better visibility of the product for the operator, although maximum wrap area was significantly less than the horizontal machines. Top speeds on horizontal machines were generally around 500–600 wires per hour, while the vertical machines could reach rates as high as 1200 per hour, depending on board quality and wiring configurations. Burroughs Corporation promotional video showing a wire wrap machine at 09:50. [http://bitsavers.trailing-edge.com/pdf/gardnerDenver/SM506753_Parameters_for_Programming_the_Gardner-Denver_Automatic_Wire-Wrap_Machine.pdf Descriptive manual for the above machine, manufactured by Gardner Denver.",
  "categories": [
    "109367229",
    "22911470",
    "22945418",
    "22969309",
    "23118434",
    "23603337",
    "24043274",
    "24745122",
    "27179417",
    "28269686",
    "63213309",
    "84360200",
    "89061585"
  ],
  "license": "CC BY-SA 4.0",
  "source_uri": "https://en.wikipedia.org/w/index.php?oldid=1350834674",
  "content_hash": "",
  "created_at": null,
  "updated_at": 1777014360.0,
  "claims": [],
  "contradictions": [],
  "confidence": 0.6,
  "csl": {
    "id": "enwiki-001350834674",
    "type": "webpage",
    "title": "Wire wrap",
    "author": [
      {
        "family": "Anticloud FZ LLE",
        "literal": "Anticloud FZ LLE"
      }
    ],
    "container-title": "encyclopegia.org",
    "publisher": "Anticloud FZ LLE",
    "publisher-place": "Dubai, United Arab Emirates",
    "URL": "https://encyclopegia.org/a/wire-wrap",
    "issued": {
      "date-parts": [
        [
          2026,
          11,
          21
        ]
      ]
    },
    "accessed": {
      "date-parts": [
        [
          2026,
          11,
          21
        ]
      ]
    },
    "license": "CC BY-SA 4.0",
    "DOI": "eo1:enwiki-001350834674",
    "isBasedOn": "https://en.wikipedia.org/w/index.php?oldid=1350834674",
    "note": "Immutable snapshot enwiki-001350834674"
  }
}