Woofer
Wikimedia disambiguation page
≈ 7 min read
Names in other languages
- EnglishWoofer
- ItalianoWoofer
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
A woofer or bass speaker is a technical term for a loudspeaker driver designed to produce low frequency and mid-frequency sounds, typically from 50 up to 2000 Hz. The name is from the onomatopoeic English word for a dog's deep bark, "woof" (in contrast to a tweeter, the name used for loudspeakers designed to reproduce high-frequency sounds, deriving from the shrill calls of birds, "tweets").
The most common design for a woofer is the electrodynamic driver, which typically uses a stiff paper cone, driven by a voice coil surrounded by a magnetic field. The voice coil is attached by adhesives to the back of the loudspeaker cone. The voice coil and the magnet form a linear electric motor.
When current flows through the voice coil, the coil moves in relation to the frame according to Fleming's left hand rule for motors, causing the coil to push or pull on the driver cone in a piston-like way. The resulting motion of the cone creates sound waves, as it moves in and out. At ordinary sound pressure levels (SPL), most humans can hear down to about 20 Hz.
Woofers are generally used to cover the lowest octaves of a loudspeaker's frequency range. In two-way loudspeaker systems, the drivers handling the lower frequencies are also obliged to cover a substantial part of the midrange, often as high as 800 to 1000 Hz; such drivers are commonly termed mid woofers.…
A woofer or bass speaker is a technical term for a loudspeaker driver designed to produce low frequency and mid-frequency sounds, typically from 50 up to 2000 Hz. The name is from the onomatopoeic English word for a dog's deep bark, "woof" (in contrast to a tweeter, the name used for loudspeakers designed to reproduce high-frequency sounds, deriving from the shrill calls of birds, "tweets").
The most common design for a woofer is the electrodynamic driver, which typically uses a stiff paper cone, driven by a voice coil surrounded by a magnetic field. The voice coil is attached by adhesives to the back of the loudspeaker cone. The voice coil and the magnet form a linear electric motor.
When current flows through the voice coil, the coil moves in relation to the frame according to Fleming's left hand rule for motors, causing the coil to push or pull on the driver cone in a piston-like way. The resulting motion of the cone creates sound waves, as it moves in and out. At ordinary sound pressure levels (SPL), most humans can hear down to about 20 Hz.
Woofers are generally used to cover the lowest octaves of a loudspeaker's frequency range. In two-way loudspeaker systems, the drivers handling the lower frequencies are also obliged to cover a substantial part of the midrange, often as high as 800 to 1000 Hz; such drivers are commonly termed mid woofers.
Since the 1990s, a type of woofer which is designed for very low frequencies only, the subwoofer, has come to be commonly used in home theater systems and PA systems to augment the bass response; subwoofers frequency response generally ranges from 45 to 100 Hz, although professional larger subwoofers found in outdoor festivals can reach frequencies down to 20 Hz.
Active loudspeakers
In 1965, Sennheiser Electronics introduced the Philharmonic sound system, which used electronics to overcome some of the problems ordinary woofer subsystems confront. They added a motion sensor to the woofer, and used the signal corresponding to its actual motion to feedback as a control input to a specially designed amplifier.
If carefully done, this can improve performance (both in 'tightness', and extension of low frequency performance) considerably at the expense of flexibility (the amplifier and the speaker are tied together permanently) and cost. As electronics costs have decreased, it has become common to have sensor-equipped woofers in inexpensive 'music systems', boom boxes, or even car audio systems.
This is usually done in an attempt to get better performance from inexpensive or undersized drivers in lightweight or poorly designed enclosures. This approach presents difficulties as not all distortion can be eliminated using servo techniques, and a poorly designed enclosure can swamp the benefits from any attempt at electronic correction.
Equalized loudspeakers
Because the characteristics of a loudspeaker can be measured, and to a considerable extent predicted, it is possible to design special circuitry that somewhat compensates for the deficiencies of a speaker system. Equalization techniques are used in most public address and sound reinforcement applications.
Here, the problem is not primarily hi-fi reproduction, but managing the acoustic environment. In this case, the equalization must be individually adjusted to match the particular characteristics of the loudspeaker systems used and the room in which they are used.
Digital filtering crossover and equalization
Computer techniques, in particular digital signal processing (DSP), make possible a higher precision crossover. By using finite impulse response (FIR) and other digital techniques, the crossovers for a bi-amped or tri-amped system can be accomplished with a precision not possible with analog filters, whether passive or active.
Furthermore, many driver peculiarities (down to and including individual variances) can be remedied at the same time such as in Klein and Hummel's recent designs. This approach is complex and thus not likely to be used in lower cost equipment.
Frame design
The frame, or basket, is the structure holding the cone, voice coil and magnet in the proper alignment. Since the voice coil gap is quite narrow (clearances are typically in the low thousandths of an inch), rigidity is important to prevent rubbing of the voice coil against the magnet structure in the gap and also avoid extraneous motions.
There are two main metal frame types, stamped and cast. Stamped baskets (usually of steel) are a lower-cost approach. The disadvantage of this type of frame is that the basket may flex if the speaker is driven at high volumes, there being resistance to bending only in certain directions.
Cast baskets are more expensive, but are usually more rigid in all directions, have better damping (reducing their own resonance), can have more intricate shapes, and are therefore usually preferred for higher quality drivers.
See also
Loudspeaker enclosure Audio crossover Full-range speaker Tweeter Super tweeter Midrange speaker Subwoofer Thiele/Small Motional Feedback
Text derived from https://en.wikipedia.org/w/index.php?oldid=1371437757 under CC BY-SA 4.0; modifications have been made.