Work function
In solid-state physics, the work function (sometimes spelled workfunction) is the minimum thermodynamic work (i.e., energy) needed to remove an electron from a solid to a point in the vacuum immediately outside the solid surface.
≈ 7 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
In solid-state physics, the work function (sometimes spelled workfunction) is the minimum thermodynamic work (i.e., energy) needed to remove an electron from a solid to a point in the vacuum immediately outside the solid surface. Here "immediately" means that the final electron position is far from the surface on the atomic scale, but still too close to the solid to be influenced by ambient electric fields in the vacuum.
The work function is not a characteristic of a bulk material, but rather a property of the surface of the material (depending on crystal face and contamination). W = -e\phi - E_{\rm F}, where is the charge of an electron, is the electrostatic potential in the vacuum nearby the surface, and is the Fermi level (electrochemical potential of electrons) inside the material.
The term is the energy of an electron at rest in the vacuum nearby the surface. is not flat due to a difference in work function. In practice, one directly controls by the voltage applied to the material through electrodes, and the work function is generally a fixed characteristic of the surface material.
Consequently, this means that when a voltage is applied to a material, the electrostatic potential produced in the vacuum will be somewhat lower than the applied voltage, the difference depending on the work function of the material surface. Rearranging the above equation, one has \phi = V - \frac{W}{e} where is the voltage of the material (as measured by a voltmeter, through an attached electrode), relative to an electrical ground that is defined as having zero Fermi level.
The fact that depends on the material surface means that the space between two dissimilar conductors will have a built-in electric field, when those conductors are in total equilibrium with each other (electrically shorted to each other, and with equal temperatures). The work function refers to removal of an electron to a position that is far enough from the surface (many nm) that the force between the electron and its image charge in the surface can be neglected.
The electron must also be close to the surface compared to the nearest edge of a crystal facet, or to any other change in the surface structure, such as a change in the material composition, surface coating or reconstruction. The built-in electric field that results from these structures, and any other ambient electric field present in the vacuum are excluded in defining the work function.
E_{\rm barrier} = W_{\rm e} determined simply by the thermionic work function of the emitter. If an electric field is applied towards the surface of the emitter, then all of the escaping electrons will be accelerated away from the emitter and absorbed into whichever material is applying the electric field.
According to Richardson's law the emitted current density (per unit area of emitter), J e (A/m 2 ), is related to the absolute temperature T e of the emitter by the equation: J_{\rm e} = -A_{\rm e} T_{\rm e}^2 e^{-E_{\rm barrier} / k T_{\rm e}} where k is the Boltzmann constant and the proportionality constant A e is the Richardson's constant of the emitter. In this case, the dependence of J e on T e can be fitted to yield W e . E_{\rm barrier} = W_{\rm c} - e (\Delta V_{\rm ce} - \Delta V_{\rm S}) where W c is the collector's thermionic work function, ΔV ce is the applied collector–emitter voltage, and ΔV S is the Seebeck voltage in the hot emitter (the influence of ΔV S is often omitted, as it is a small contribution of order 10 mV).
The resulting current density J c through the collector (per unit of collector area) is again given by Richardson's Law, except now J_{\rm c} = A T_{\rm e}^2 e^{-E_{\rm barrier}/kT_{\rm e}} where A is a Richardson-type constant that depends on the collector material but may also depend on the emitter material, and the diode geometry. In this case, the dependence of J c on T e , or on ΔV ce , can be fitted to yield W c . This retarding potential method is one of the simplest and oldest methods of measuring work functions, and is advantageous since the measured material (collector) is not required to survive high temperatures. \hbar \omega = W_{\rm e} where W e is the work function of the emitter.
Photoelectric measurements require a great deal of care, as an incorrectly designed experimental geometry can result in an erroneous measurement of work function. This may be responsible for the large variation in work function values in scientific literature.
Moreover, the minimum energy can be misleading in materials where there are no actual electron states at the Fermi level that are available for excitation. For example, in a semiconductor the minimum photon energy would actually correspond to the valence band edge rather than work function.
Of course, the photoelectric effect may be used in the retarding mode, as with the thermionic apparatus described above. In the retarding case, the dark collector's work function is measured instead. e\Delta V_{\rm sp} = W_{\rm s} - W_{\rm p}, \quad \text{when}~\phi~\text{is flat}.
Since the experimenter controls and knows ΔV sp , then finding the flat vacuum condition gives directly the work function difference between the two materials. The only question is, how to detect the flat vacuum condition? Typically, the electric field is detected by varying the distance between the sample and probe.
When the distance is changed but ΔV sp is held constant, a current will flow due to the change in capacitance. This current is proportional to the vacuum electric field, and so when the electric field is neutralized no current will flow.
Although the Kelvin probe technique only measures a work function difference, it is possible to obtain an absolute work function by first calibrating the probe against a reference material (with known work function) and then using the same probe to measure a desired sample. The Kelvin probe technique can be used to obtain work function maps of a surface with extremely high spatial resolution, by using a sharp tip for the probe (see Kelvin probe force microscope).
W = E_{\rm EA} + E_{\rm C} - E_{\rm F} where E C is taken at the surface. From this one might expect that by doping the bulk of the semiconductor, the work function can be tuned. In reality, however, the energies of the bands near the surface are often pinned to the Fermi level, due to the influence of surface states.
If there is a large density of surface states, then the work function of the semiconductor will show a very weak dependence on doping or electric field. The electron behavior in metals varies with temperature and is largely reflected by the electron work function.
A theoretical model for predicting the temperature dependence of the electron work function, developed by Rahemi et al. explains the underlying mechanism and predicts this temperature dependence for various crystal structures via calculable and measurable parameters. In general, as the temperature increases, the EWF decreases via \varphi(T)=\varphi_0-\gamma\frac{(k_\text{B}T)^2}{\varphi_0} and \gamma is a calculable material property which is dependent on the crystal structure (for example, BCC, FCC). \varphi_0 is the electron work function at T=0 and k_\text{B} is constant throughout the change.
Work function of polymeric insulators (Table 2.1) Work function of diamond and doped carbon Work functions of common metals Work functions of various metals for the photoelectric effect Physics of free surfaces of semiconductors
Text derived from https://en.wikipedia.org/w/index.php?oldid=1368612509 under CC BY-SA 4.0; modifications have been made.