XLR connector

The XLR connector (also called a Cannon plug or Cannon connector) is a type of electrical connector primarily used in professional audio, video, and stage lighting equipment.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 5 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

The XLR connector (also called a Cannon plug or Cannon connector) is a type of electrical connector primarily used in professional audio, video, and stage lighting equipment. XLR connectors are cylindrical, with three to seven connector pins, and are often employed for analog balanced audio interconnections, AES3 digital audio, portable intercom, DMX512 lighting control, and for low-voltage power supply.

XLR connectors are part of the international standard for dimensions, IEC 61076-2-103. The XLR connector resembles the DIN connector, but is larger, more robust and physically incompatible.

The generic term XLR began as a trademark of Cannon Electric, with the letters standing for X model connector with an added latch (L) feature, and resilient (R) neoprene rubber surrounding the female contacts.

Obsolete patterns

power connections. The connecting pins in the male connector are recessed, and the sockets in the female connectors are shrouded for safety. This example is a panel socket, used as a power input from the male plug, though they were also used in the opposite configuration.

Many other types of connectors using the XLR type shell exist, with various pin configurations. One is the now obsolete three-pin power pattern connector manufactured by ITT Cannon.

The power Cannon (also called the XLR-LNE connector) had shrouded pins and red insulation; it was intended as a mains power plug, an alternative to the IEC 60320 series of connectors, but was only used on a few pieces of equipment.

Two-pin (XLR2)

A two-pin variant was used as the DC power input socket on Yamaha's 1970s CP-series 'Electric Grand' pianos (CP-60, CP-70 and CP-80).

Three-pin in audio use

XLR3-12C (line), Switchcraft X3F (line), Neutrik NC3MP panel, Neutrik NC3FP panel combo jack. EIA Standard RS-297-A describes the use of the three-pin XLR - known as XLR3 - for balanced audio signal level applications: Prior to the introduction of this standard, the wiring of pins 2 and 3 varied.

The pin 2 "hot" and pin 3 "cold" convention was typically used by European and Japanese equipment manufacturers, but American companies used pin 3 "hot" and pin 2 "cold". This caused problems when interconnecting equipment with unbalanced connections. The pin 3 "hot" convention is now obsolete but is still found on vintage equipment.

Pin 1 has always been ground and/or shield if the cable is shielded, and many connectors connect it internally to the connector shell or case. Although covered in industry technical standards, there is still some disagreement on the best way to handle the use of pin 1 for grounding (earthing).

The main controversy is whether the shell of the connector should be connected to pin 1 or the shield, or left floating. AES standards mentioned above recommend that shells of cable-mounted connectors should never be connected to pin 1 or the shield, because inadvertent contact of the shell with another grounded surface while in use can create unwanted current paths for fault current, potentially causing hum and other noise.

On the other hand, equipment containing active circuitry should always have pin 1 connected to the conductive enclosure of the equipment as close as possible to the point where the signal enters the enclosure. The argument centers on the radio frequency shielding provided by the shell of the connector, which may be reduced if it is left floating.

An alternative solution is to connect the shell to pin 1 and the shield through a small-value capacitor, providing RF shielding but allowing very little audio-frequency current to flow. This capability can be built into a fixed jack or a cable terminated with XLR connectors.

The standard signal flow for audio in XLR connectors is that the output is a male connector and the input is female. In other words, the pins on the plug point in the direction of signal flow. Phantom power, if used, originates from the socket and flows into the plug (the opposite direction to the signal and the normal direction for power circuits).

The voltages of microphone and line-level audio signals are not hazardous. The male XLR is usually incorporated in the body of a microphone. Since equipment often requires an input on a TRS phone jack or an XLR connector, Neutrik and Amphenol offer several models of combination connectors that accept both XLR and TS or TRS phone plugs.

Clear-Com, Telex, RTS and many other production intercom systems use four-pin XLR connectors for attaching monaural intercom headsets or handsets. The standard pinout for four-pin XLR headsets is: Pin 1 = Microphone ground (screen/shield); Pin 2 = Microphone signal ("hot") input; Pin 3 = Headphone ground (return); Pin 4 = Headphone signal ("hot") output.

XLD keyed variant

The XLD connector is a proposed keyed variant of the XLR connector. The keys prevent accidental mixing of XLR and XLD connectors. XLD plugs and sockets are used mostly in professional audio and video electronics cabling applications.

The XLD connector is proposed by the Audio Engineering Society AES42 digital microphone interface standard. The connectors are similar to XLR but with an extra coding key and groove that allows control over the intermating of XLD plugs and XLR sockets. A connector with the coding key installed will not mate with a connector that does not have the matching groove.

By suitably keying connectors, analog microphones can be protected from damage by the high-current digital phantom power supply provided for digital microphones.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1377861063 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

27 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.