{
  "id": "enwiki-001355687006",
  "slug": "zero-insertion-force",
  "title": "Zero insertion force",
  "qid": "",
  "lead": "-28W package ) (wide SOIC-28) in a ZIF socket Zero insertion force (ZIF) is a type of IC socket or electrical connector that requires very little (but not literally zero) force for insertion. With a ZIF socket, before the IC is inserted, a lever or slider on the side of the socket is moved, pushing all the sprung contacts apart so that the IC can be inserted with very little force - generally the weight of the IC itself is sufficient and no external downward force is required. The lever is then moved back, allowing the contacts to close and grip the pins of the IC. ZIF sockets are much more expensive than standard IC sockets and also tend to take up a larger board area due to the space taken up by the lever mechanism. Typically, they are only used when there is a specific need for them, such as an EPROM programmer, for prototyping work or for some large processor chips where non-ZIF sockets are impractical.",
  "body": "-28W package ) (wide SOIC-28) in a ZIF socket Zero insertion force (ZIF) is a type of IC socket or electrical connector that requires very little (but not literally zero) force for insertion. With a ZIF socket, before the IC is inserted, a lever or slider on the side of the socket is moved, pushing all the sprung contacts apart so that the IC can be inserted with very little force - generally the weight of the IC itself is sufficient and no external downward force is required. The lever is then moved back, allowing the contacts to close and grip the pins of the IC. ZIF sockets are much more expensive than standard IC sockets and also tend to take up a larger board area due to the space taken up by the lever mechanism. Typically, they are only used when there is a specific need for them, such as an EPROM programmer, for prototyping work or for some large processor chips where non-ZIF sockets are impractical. ==Universal test sockets== , with a dual in-line ZIF socket Standard DIP packages come in a number of widths (measured between pin centers), with 0.3 in (7.62&nbsp;mm) and 0.6 in (15.24&nbsp;mm) being the most common. To allow the design of programmers and similar devices that support a range of devices universal test sockets are produced. These have wide slots into which the pins drop allowing devices of differing widths to be inserted. ==Ball grid array sockets== ZIF sockets can be used for ball grid array chips, particularly during development. These sockets tend to be unreliable, failing to grab all the solder balls. Another type of BGA socket, also free of insertion force but not a \"ZIF socket\" in the traditional sense, does a better job by using spring pins to push up underneath the balls. ==ZIF wire-to-board connectors== that connects to them ZIF wire-to-board connectors are used for attaching wires to printed circuit boards inside electronic equipment. An example would be the cable between the LCD screen and motherboard in laptops. The wires, often formed into a ribbon cable, are pre-stripped and the bare ends are placed inside the connector. The two sliding parts of the connector are then pushed together, causing it to grip the wires. The most important advantage of this system is that it does not require a mating half to be fitted to the wire ends, therefore saving space and cost inside miniaturised equipment. See flexible flat cable. ==Hard disk drives== ZIF tape connections are used for connecting Parallel ATA and Serial ATA disk drives (mostly drives in the 1.8-inch form factor). PATA hard drives with ZIF-style connectors were used primarily in the design of ultra-portable notebooks. They have since been phased out, as SATA has a relatively small-form-factor connector by default. M.2 (or mSATA in older machines) used where even smaller form factors are required. Internally, nearly all hard drives use ZIF tape to connect their circuit board to their platter motor. ZIF tape connections were also heavily used in the design of the iPod range of portable media players, not just for the hard drive but also for other connections from the main circuit board. Three types of ZIF connectors are known to exist on 1.8 inch PATA drives. ZIF-24, ZIF-40, and ZIF-50 have 24, 40, and 50 pins respectively. ==See also== Dual in-line package Flexible flat cable ==References== ==External links== Zero Insertion Force (ZIF) Sockets. / Microprocessor Types and Specifications. Informit, Jun 8, 2001. 4.2.5 ZIF Contact Design. / IC Component Sockets. John Wiley & Sons, 2004. P. 86. ISBN 978-0-471-46050-3 Zero Insertion Force Socket (ZIF Socket) . Technopedia.",
  "categories": [
    "125972575",
    "21493616",
    "23004968",
    "23118434",
    "23603337",
    "24043274",
    "24745122",
    "28269686",
    "48861464",
    "89061539"
  ],
  "license": "CC BY-SA 4.0",
  "source_uri": "https://en.wikipedia.org/w/index.php?oldid=1355687006",
  "content_hash": "",
  "created_at": null,
  "updated_at": 1779518764.0,
  "claims": [],
  "contradictions": [],
  "confidence": 0.6,
  "csl": {
    "id": "enwiki-001355687006",
    "type": "webpage",
    "title": "Zero insertion force",
    "author": [
      {
        "family": "Anticloud FZ LLE",
        "literal": "Anticloud FZ LLE"
      }
    ],
    "container-title": "encyclopegia.org",
    "publisher": "Anticloud FZ LLE",
    "publisher-place": "Dubai, United Arab Emirates",
    "URL": "https://encyclopegia.org/a/zero-insertion-force",
    "issued": {
      "date-parts": [
        [
          2026,
          11,
          20
        ]
      ]
    },
    "accessed": {
      "date-parts": [
        [
          2026,
          11,
          20
        ]
      ]
    },
    "license": "CC BY-SA 4.0",
    "DOI": "eo1:enwiki-001355687006",
    "isBasedOn": "https://en.wikipedia.org/w/index.php?oldid=1355687006",
    "note": "Immutable snapshot enwiki-001355687006"
  }
}