Automatisk frekvenskontrol

radio circuit

Uses your system voice; voice and rate in settings.

The name shown is in da. The article below is in English and is not a translation.

≈ 3 min read

Cite, export and learn8 citation formats · 8 exports · lesson and quiz

Names in other languages

  • Polskiautomatyczna regulacja częstotliwościARCz
  • etSageduse automaatne järelhäälestus
  • Magyarautomatikus frekvenciaszabályozás
  • РусскийАвтоматическая подстройка частоты
  • fiautomaattinen taajuudensäätö
  • DeutschAutomatic frequency control
  • Englishautomatic frequency controlAFC
  • ItalianoAutomatic Frequency Control
  • NederlandsAutomatic frequency control
  • SvenskaAutomatisk frekvenskontroll
  • daAutomatisk frekvenskontrolAutomatisk frekvensstyring
  • 日本語自動周波数制御
  • 中文自动频率控制
  • 中文自动频率控制
  • 简体中文自动频率控制
  • 繁體中文自動頻率控制
  • УкраїнськаАПЧ

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

In radio equipment, Automatic Frequency Control (AFC), also called Automatic Fine Tuning (AFT), is a method or circuit to automatically keep a resonant circuit tuned to the frequency of an incoming radio signal.[1] It is primarily used in radio receivers to keep the receiver tuned to the frequency of the desired station.[citation needed]

In radio communication, AFC is needed because, after the bandpass frequency of a receiver is tuned to the frequency of a transmitter, the two frequencies may drift apart, interrupting the reception. This can be caused by a poorly controlled transmitter frequency, but the most common cause is drift of the center bandpass frequency of the receiver, due to thermal or mechanical drift in the values of the electronic components.[citation needed]

Assuming that a receiver is nearly tuned to the desired frequency, the AFC circuit in the receiver develops an error voltage proportional to the degree to which the receiver is mistuned. This error voltage is then fed back to the tuning circuit in such a way that the tuning error is reduced.[2] In most frequency modulation (FM) detectors, an error voltage of this type is easily available.[citation needed] See Negative feedback.

Use

edit edit source

AFC was mainly used in radios and television sets around the mid-20th century. In the 1970s, receivers began to be designed using frequency synthesizer circuits, which synthesized the receiver's input frequency from a crystal oscillator using the vibrations of an ultra-stable quartz crystal. These maintained sufficiently stable frequencies that AFCs were no longer needed.

See also

edit edit source

Notes

edit edit source
  1. ^ Rider 1937, pp. 2-3. Wikipedia revision 1295153610, retrieved 2026-11-18
  2. ^ Rider 1937, p. 7. Wikipedia revision 1295153610, retrieved 2026-11-18

References

edit edit source edit edit source

Text derived from https://en.wikipedia.org/w/index.php?oldid=1295153610 under CC BY-SA 4.0; modifications have been made.

Words in each sectionUseUseUse: 57 words57NotesNotesNotes: 21 words21See alsoSee alsoSee also: 12 words12
Words in each section. Measured from the stored article body; sections below the minimum are not plotted.

Provenance

snapshot automatic-frequency-control-025957-00c02b53fce7bb74 · hash 00c02b53fce7bb74415562da22cec145f6f87f599f498e262b650f67f348e3bf · captured 2025-06-11 · ledger · version history

Cite this page as: encyclopegia.org, “Automatisk frekvenskontrol”, snapshot automatic-frequency-control-025957-00c02b53fce7bb74. https://encyclopegia.org/a/automatic-frequency-control