DBm0
≈ 4 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
dBm0 is an abbreviation for the power in decibel-milliwatts (dBm) measured at a zero transmission level point (ZLP). dBm0 is a concept used (amongst other areas) in audio/telephony processing since it allows a smooth integration of analog and digital chains. Notably, for A-law and μ-law codecs the standards define a sequence which has a output. The unit dBm0 is used to describe levels of digital as well as analog signals and is derived from its counterpart dBm. Although today dBm0 may be considered supplanted by the similar unit decibels relative to full scale (dBFS) (discussion at ), dBm0 can be viewed as connecting both the old world of analog telecommunication and the new world of digital communication. The level corresponds to the digital milliwatt (DMW) and is defined as the absolute power level at a digital reference point of the same signal that would be measured as the absolute power level, in dBm, if the reference point was analog. The absolute power in dBm scale for a power in milliwatts (mW) is defined as: 10 \log_{10} \frac{P}{1~\text{[mW]}} \, . When the test impedance is resistive, can be referred to a voltage of , which results in a reference active power of . Then corresponds to an overload level of approximately in the analog-to-digital conversion.…
dBm0 is an abbreviation for the power in decibel-milliwatts (dBm) measured at a zero transmission level point (ZLP). dBm0 is a concept used (amongst other areas) in audio/telephony processing since it allows a smooth integration of analog and digital chains. Notably, for A-law and μ-law codecs the standards define a sequence which has a output. The unit dBm0 is used to describe levels of digital as well as analog signals and is derived from its counterpart dBm. Although today dBm0 may be considered supplanted by the similar unit decibels relative to full scale (dBFS) (discussion at ), dBm0 can be viewed as connecting both the old world of analog telecommunication and the new world of digital communication. The level corresponds to the digital milliwatt (DMW) and is defined as the absolute power level at a digital reference point of the same signal that would be measured as the absolute power level, in dBm, if the reference point was analog. The absolute power in dBm scale for a power in milliwatts (mW) is defined as: 10 \log_{10} \frac{P}{1~\text{[mW]}} \, . When the test impedance is resistive, can be referred to a voltage of , which results in a reference active power of . Then corresponds to an overload level of approximately in the analog-to-digital conversion. Given a sinusoid signal of RMS, the power at a zero transmission level point is: P = \frac{(0.775 [\mathrm{V}])^2}{600 [\Omega]} = 0.001 [\mathrm{W}] = 1 [\mathrm{mW}] = 0 [\mathrm{dBm}]\,, and the voltage level at the ZLP is: L = 10*\log_{10}\left( \frac{0.775 [\mathrm{V}]}{1 [\mathrm{V}]} \right)^2 \approx -2.214 [\mathrm{dBV}]. TIA-810 characterizes: When a analog signal is applied to the coder input, a digital code is present at the digital reference. In general, when a digital code is applied to the decoder, a analog signal appears at the decoder output. More specifically, when the periodic sequence as given in Table 2, in either mu-law or A-law as appropriate, is applied to the decoder at the digital reference point, a , sine-wave signal appears at the decoder output. is 3.14 (A-law) or 3.17 (mu-law) dB below digital full scale. In all standards, dBm0 is always an RMS unit. Peaks are described in a different way, sometimes by mentioning the margin to overload or clipping. The nominal downlink level in mobile phone telecommunication at the point of interconnection is .
Notes
References
Sources
ETSI G.711
Text derived from https://en.wikipedia.org/w/index.php?oldid=1327674791 under CC BY-SA 4.0; modifications have been made.