DisplayPort

Uses your system voice; voice and rate in settings.

Snapshot

≈ 11 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

DisplayPort (DP) is a digital interface used to connect a video source, such as a computer, to a display device like a monitor. Developed by the Video Electronics Standards Association (VESA), it can also carry digital audio, USB, and other types of data over a single cable. Introduced in 2008, DisplayPort was designed to replace older standards like VGA, DVI, and FPD-Link. While not directly compatible with these formats, adapters are available for connecting to HDMI, DVI, VGA, and other interfaces. Unlike older interfaces, DisplayPort uses packet-based transmission, similar to how data is sent over USB or Ethernet. The design enables support for high resolutions and adding new features without changing the connector. DisplayPort includes an auxiliary data channel used for device control and automatic configuration between source and display devices. It supports standards such as Display Data Channel (DDC), Extended Display Identification Data (EDID), Monitor Control Command Set (MCCS), and VESA Display Power Management Signaling (DPMS). Some implementations also support Consumer Electronics Control (CEC), which allows devices to send commands to each other and be operated using a single remote control.

DisplayPort (DP) is a digital interface used to connect a video source, such as a computer, to a display device like a monitor. Developed by the Video Electronics Standards Association (VESA), it can also carry digital audio, USB, and other types of data over a single cable. Introduced in 2008, DisplayPort was designed to replace older standards like VGA, DVI, and FPD-Link. While not directly compatible with these formats, adapters are available for connecting to HDMI, DVI, VGA, and other interfaces. Unlike older interfaces, DisplayPort uses packet-based transmission, similar to how data is sent over USB or Ethernet. The design enables support for high resolutions and adding new features without changing the connector. DisplayPort includes an auxiliary data channel used for device control and automatic configuration between source and display devices. It supports standards such as Display Data Channel (DDC), Extended Display Identification Data (EDID), Monitor Control Command Set (MCCS), and VESA Display Power Management Signaling (DPMS). Some implementations also support Consumer Electronics Control (CEC), which allows devices to send commands to each other and be operated using a single remote control.

1.0 to 1.1

The first version, 1.0, was approved by VESA on 3 May 2006. Version 1.1 was ratified on 2 April 2007, and version 1.1a on 11 January 2008. DisplayPort 1.0–1.1a allow a maximum bandwidth of 10.8 Gbit/s (8.64 Gbit/s data rate) over a standard 4-lane main link. DisplayPort cables up to 2 meters in length are required to support the full 10.8 Gbit/s bandwidth. DisplayPort 1.1 allows devices to implement alternative link layers such as fiber optic, allowing a much longer reach between source and display without signal degradation, although alternative implementations are not standardized. It also includes HDCP in addition to DisplayPort Content Protection (DPCP). The DisplayPort 1.1a standard can be downloaded free of charge from the VESA website.

1.2a

DisplayPort version 1.2a was released in January 20131 and may optionally include VESA's Adaptive Sync. AMD's FreeSync uses the DisplayPort Adaptive-Sync feature for operation. FreeSync was first demonstrated at CES 2014 on a Toshiba Satellite laptop by making use of the Panel-Self-Refresh (PSR) feature from the Embedded DisplayPort standard, and after a proposal from AMD, VESA later adapted the Panel-Self-Refresh feature for use in standalone displays and added it as an optional feature of the main DisplayPort standard under the name "Adaptive-Sync" in version 1.2a. As it is an optional feature, support for Adaptive-Sync is not required for a display to be DisplayPort 1.2a-compliant. RBR: 4 × 1.62 Gbit/s = 6.48 Gbit/s bandwidth (data rate of 5.184 Gbit/s or 648 MB/s with 8b/10b encoding) HBR: 4 × 2.70 Gbit/s = 10.80 Gbit/s bandwidth (data rate of 8.64 Gbit/s or 1.08 GB/s) HBR2: 4 × 5.40 Gbit/s = 21.60 Gbit/s bandwidth (data rate of 17.28 Gbit/s or 2.16 GB/s) HBR3: 4 × 8.10 Gbit/s = 32.40 Gbit/s bandwidth (data rate of 25.92 Gbit/s or 3.24 GB/s) UHBR 10: 4 × 10.0 Gbit/s = 40.00 Gbit/s bandwidth (data rate of 38.6 9 Gbit/s or 4.84 GB/s with 128b/132b encoding and FEC) UHBR 13.5: 4 × 13.5 Gbit/s = 54.00 Gbit/s bandwidth (data rate of 52.2 2 Gbit/s or 6.52 GB/s) UHBR 20: 4 × 20.0 Gbit/s = 80.00 Gbit/s bandwidth (data rate of 77.3 7 Gbit/s or 9.69 GB/s) The transmission mode used by the DisplayPort main link is negotiated by the source and sink device (the device accepting the signal) when a connection is made, through a process called Link Training. This process determines the maximum possible speed of the connection. If the quality of the DisplayPort cable is insufficient to reliably handle HBR2 speeds for example, the DisplayPort devices will detect this and switch down to a lower mode to maintain a stable connection. The link can be re-negotiated at any time if a loss of synchronization is detected. Audio data is transmitted across the main link during the video blanking intervals (short pauses between each line and frame of video data).

DisplayPort Dual-Mode (DP++)

DisplayPort Dual-Mode (DP++), also called Dual-Mode DisplayPort, is a standard which allows DisplayPort sources to use simple level-shifting adapters to connect to HDMI or DVI displays. Dual-mode is an optional feature, so not all DisplayPort sources necessarily support sending DVI/HDMI signals, though in practice nearly all devices do. Officially, the "DP++" logo should be used to indicate a DP port that supports dual-mode, but most modern devices do not use the logo. Devices which implement dual-mode will detect that a DVI or HDMI adapter is attached, and send DVI/HDMI TMDS signals instead of DisplayPort signals. The original DisplayPort Dual-Mode standard (version 1.0), used in DisplayPort 1.1 devices, only supported TMDS clock speeds of up to 165 MHz (4.95 Gbit/s bandwidth). This is equivalent to HDMI 1.2, and is sufficient for up to at 60 Hz. In 2013, VESA released the Dual-Mode 1.1 standard, which added support for up to a 300 MHz TMDS clock (9.00 Gbit/s bandwidth), and is used in newer DisplayPort 1.2 devices. This is slightly less than the 340 MHz maximum of HDMI 1.4, and is sufficient for up to at 120 Hz, at 60 Hz, or at 30 Hz. Older adapters, which were only capable of the 165 MHz speed, were retroactively termed "Type 1" adapters, with the new 300 MHz adapters being called "Type 2".

Multi-Stream Transport (MST)

Multi-Stream Transport is a feature first introduced in the DisplayPort 1.2 standard. It allows multiple independent displays to be driven from a single DP port on the source devices by multiplexing several video streams into a single stream and sending it to a branch device, which demultiplexes the signal into the original streams. Branch devices are commonly found in the form of an MST hub, which plugs into a single DP input port and provides multiple outputs, but it can also be implemented on a display internally to provide a DP output port for daisy-chaining, effectively embedding a 2-port MST hub inside the display. Theoretically, up to 63 displays can be supported, but the combined data rate requirements of all the displays cannot exceed the limits of a single DP port (17.28 Gbit/s for a DP 1.2 port, or 25.92 Gbit/s for a DP 1.3/1.4 port). In addition, the maximum number of links between the source and any device (i.e. the maximum length of a daisy-chain) is 7, and the maximum number of physical output ports on each branch device (such as a hub) is 7. With the release of MST, standard single-display operation has been retroactively named "SST" mode (Single-Stream Transport). Daisy-chaining is a feature that must be specifically supported by each intermediary display; not all DisplayPort 1.2 devices support it. Daisy-chaining requires a dedicated DisplayPort output port on the display. Standard DisplayPort input ports found on most displays cannot be used as a daisy-chain output. Only the last display in the daisy-chain does not need to support the feature specifically or have a DP output port. DisplayPort 1.1 displays can also be connected to MST hubs, and can be part of a DisplayPort daisy-chain if it is the last display in the chain. The host system's software also needs to support MST for hubs or daisy-chains to work. While Microsoft Windows environments have full support for it, Apple operating systems currently do not support MST hubs or DisplayPort daisy-chaining as of macOS 10.15 ("Catalina"). DisplayPort-to-DVI and DisplayPort-to-HDMI adapters/cables may or may not function from an MST output port; support for this depends on the specific device. MST is supported by USB Type-C DisplayPort Alternate Mode, so standard DisplayPort daisy-chains and MST hubs do function from Type-C sources with a simple Type-C to DisplayPort adapter.

Content protection

DisplayPort 1.0 includes optional DPCP (DisplayPort Content Protection) from Philips, which uses 128-bit AES encryption. It also features full authentication and session key establishment. Each encryption session is independent, and it has an independent revocation system. This portion of the standard is licensed separately. It also adds the ability to verify the proximity of the receiver and transmitter, a technique intended to ensure users are not bypassing the content protection system to send data out to distant, unauthorized users. DisplayPort 1.1 added optional implementation of industry-standard 56-bit HDCP (High-bandwidth Digital Content Protection) revision 1.3, which requires separate licensing from the Digital Content Protection LLC. DisplayPort 1.3 added support for HDCP 2.2, which is also used by HDMI 2.0.

Participating companies

The following companies have participated in preparing the drafts of DisplayPort, eDP, iDP, DDM or DSC standards: Agilent Altera AMD Graphics Product Group Analogix Apple Astrodesign BenQ Broadcom Corporation Chi Mei Optoelectronics Chrontel Dell Display Labs Foxconn Electronics FuturePlus Systems Genesis Microchip Gigabyte Technology Hardent Hewlett-Packard Hosiden Hirose Electric Group Intel intoPIX I-PEX Integrated Device Technology JAE Electronics Kawasaki Microelectronics (K-Micro) Keysight Technologies Lenovo LG Display Luxtera Molex NEC NVIDIA NXP Semiconductors Xi3 Corporation Parade Technologies Realtek Semiconductor Samsung SMK STMicroelectronics Synaptics Inc. SyntheSys Research Inc. Teledyne LeCroy (QuantumData) Tektronix Texas Instruments TLi Tyco Electronics ViewSonic VTM The following companies have additionally announced their intention to implement DisplayPort, eDP or iDP: Acer ASRock Biostar Chroma BlackBerry Circuit Assembly DataPro Eizo Fujitsu Hall Research Technologies ITE Tech. Matrox Graphics Micro-Star International MStar Semiconductor Novatek Microelectronics Corp. Palit Microsystems Ltd. Pioneer Corporation S3 Graphics Toshiba Philips Quantum Data Sparkle Computer Unigraf Xitrix

Text derived from https://en.wikipedia.org/w/index.php?oldid=1376835214 under CC BY-SA 4.0; modifications have been made.

References

  1. ↩Wikipedia release date (×1) · confidence 0.95 https://en.wikipedia.org/w/index.php?oldid=1376835214

Sources cited in this revision

Extracted from the cited revision's reference blocks; absent citations are not invented.