Ford FE engine
≈ 32 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
The Ford FE engine is a big-block V8 engine produced in multiple displacements over two generations by the Ford Motor Company and used in vehicles sold in the North American market between 1958 and 1976. The FE, derived from "Ford-Edsel", was introduced just four years after the short-lived Ford Y-block engine, which American cars and trucks were outgrowing. It was designed with room to be significantly expanded, and manufactured both as a top-oiler and side-oiler, and in displacements between and . Versions of the FE line designed for use in medium and heavy trucks and school buses from 19641 through 1978 were known as "FT," for "Ford Truck," and differed primarily by having steel (instead of nodular iron) crankshafts, larger crank snouts, smaller ports and valves, different distributor shafts, different water pumps, and a greater use of iron for its parts. The FE block was manufactured by using a thin-wall casting technique, where Ford engineers determined the required amount of metal and re-engineered the casting process to allow for consistent dimensional results. A Ford FE from the factory weighed with all-iron components, while similar 7-liter offerings from GM and Chrysler weighed over . With an aluminum intake and aluminum water pump, the FE could be reduced to under for racing.…
The Ford FE engine is a big-block V8 engine produced in multiple displacements over two generations by the Ford Motor Company and used in vehicles sold in the North American market between 1958 and 1976. The FE, derived from "Ford-Edsel", was introduced just four years after the short-lived Ford Y-block engine, which American cars and trucks were outgrowing. It was designed with room to be significantly expanded, and manufactured both as a top-oiler and side-oiler, and in displacements between and . Versions of the FE line designed for use in medium and heavy trucks and school buses from 1964 through 1978 were known as "FT," for "Ford Truck," and differed primarily by having steel (instead of nodular iron) crankshafts, larger crank snouts, smaller ports and valves, different distributor shafts, different water pumps, and a greater use of iron for its parts. The FE block was manufactured by using a thin-wall casting technique, where Ford engineers determined the required amount of metal and re-engineered the casting process to allow for consistent dimensional results. A Ford FE from the factory weighed with all-iron components, while similar 7-liter offerings from GM and Chrysler weighed over . With an aluminum intake and aluminum water pump, the FE could be reduced to under for racing. The engine was produced in 406 and 427 cubic-inch competition versions and famously powered Ford GT40 MkIIs to endurance-racing domination in the 24 hours of Le Mans during the mid-1960s.
Description
The FE and FT engines are big-block designs, referred to as Y-block because the cylinder block casting extends below the crankshaft centerline, giving great rigidity and support to the crankshaft's main bearings. In these engines, the casting extends below the crankshaft centerline, which is more than an inch below the bottom of the crank journals. Blocks were cast in two major groups: top-oiler and side-oiler. The top-oiler block sent oil to the top center first; the side-oiler block sent oil along a passage located on the lower side of the block first. All FE and FT engines have a bore spacing of and a deck height (distance from crank center to top of block) of . The main journal (crankshaft bearing) diameter is . Within the family of Ford engines of the time, the FE was neither the largest nor smallest block. FE engines were made in a wide variety of configurations, including: Carbureted, including single two-barrel, single four-barrel, dual four-barrel, triple two-barrel, and quad Webers, or fuel injected With a top- or side-oiling block With low-rise, medium-rise, high-rise, tunnel-port, or SOHC intake manifolds The low-rise intake, designed to fit under a low hoodline, was the first. The high-rise intake required a hood bubble for clearance. While the low- and medium-rise heads could be used in combination with either low- or medium-rise intakes, the high-rise head required a high-rise intake due to the increased height of the intake port. The medium-rise intake port is shorter and wider than the low-rise port. The high-rise ports are taller than either the low- or medium-rise ports. Low-rise intakes have the carburetor placed relatively low; the air-fuel mix must follow a more convoluted path to the combustion chambers. A high-rise intake places the carburetor approximately higher so the air-fuel mixture has a straighter path. The tunnel-port and SOHC heads require their own matching intakes. Within the major head groups, differences also existed in combustion-chamber designs - small chambers, machined ones, and large ones. The sizes and types of chambers affect the compression ratio and the overall performance characteristics of the engine.
Generations
Generation 1
332
The "332" was the original FE engine, with a displacement of , the series' smallest. It had bore and a stroke, and was used in Ford-brand cars in 1958 and 1959, domestically marketed U.S.- and Canadian-built Edsel-brand cars in 1959, and in export-configured 1958 and 1959 Edsels. The two-barrel version produced ; a Holley or Autolite four-barrel version made .
332 engine configurations and applications
4V, 9.5:1 — at 4600 rpm and at 2800 rpm 1958 Ford 1958 Edsel Ranger, Pacer, Villager, Roundup. and Bermuda overseas export vehicles only 2V, 8.9:1 — at 4600 rpm and at 2200 rpm 1959 Ford 1959 Edsel Corsair and Villager, standard equipment, (called "Express V8")
352
Introduced in 1958 as part of the Interceptor line of Ford V8 engines, the Ford 352 of actual displacement was the replacement for the Lincoln Y-block. It is a stroked 332 with stroke and a bore, and was rated from with a two-barrel carburetor to over on the four-barrel models. When these engines were introduced, they were called Interceptor V-8 on the base models and Interceptor Special V-8 on the four-barrel models. The 1958 H VIN-coded 352 was designated as Interceptor V-8 Thunderbird Special. The Interceptor was the base-performance engine in 1958. For the 1959 model year, the FE engine series was renamed the Thunderbird V-8 and the Thunderbird Special V-8. When installed in Mercury vehicles, these engines were named "Marauder". This series of engines usually weighed over . In 1960, Ford created a high-performance version of the 352 rated at ; it featured an aluminum intake manifold, Holley 4100 four-barrel carburetor, cast-iron header-style exhaust manifolds, 10.5:1 compression ratio, and solid lifters.
352 engine configurations and applications
2V 8.4:1 — at 4000 rpm and at 2800 rpm 1965–1967 Ford F-Series 8.9:1 — at 4400 rpm and at 2400 rpm 1961–1963 Ford 1961–1963 Mercury (1961 Meteor and 1961–1963 Monterey, Commuter Wagon, Colony Park) 4V 10.2:1 — at 4600 rpm and at 2800 rpm 1958 Ford Interceptor 1958–1959 Ford 1958–1959 Ford Thunderbird 9.6:1 — at 4600 rpm and at 2800 rpm 1960 Ford 1960 Edsel 1960 Ford Thunderbird 10.6:1 — at 6000 rpm and at 3400 rpm 1960 Ford 8.9:1 — at 4400 rpm and at 2400 rpm 1960 Ford 9.3:1 — at 4400 rpm and at 2800 rpm 1964–1966 Ford
361 Edsel
Edsel 361 engines were assembled in Cleveland, Ohio, and Dearborn, Michigan. They were standard equipment in the 1958 Edsel Ranger, Pacer, Villager, Roundup, and Bermuda. The Edsel 361 was the first FE block engine to be offered for sale in any market, having been introduced to the public in the U.S. on September 4, 1957, almost two months before any 1958 Fords were sold. The 361 CID 4V FE engine was also sold on 1959 Edsels in the U.S. and Canada, and 1958 and 1959 Ford- and Meteor-brand automobiles in Canada in place of the 352, which was not available with any Ford Motor Company of Canada brand until the 1960 model year. Edsel 361 engines were available to U.S. law enforcement agencies and state and municipal emergency services purchasing fleet Fords as the 1958 Ford "Police Power Pack".
361 Edsel engine configurations and applications
4V 10.5:1 compression ratio at 4600 rpm Torque at 2800 rpm × Bore/Stroke 4-bbl Holley or Ford (Autolite) carburetor Pushrod overhead valve Angle-wedge machined combustion chamber Firing order: 1-5-4-2-6-3-7-8 Cylinder numbering (front-to-rear): Right 1-2-3-4 Left 5-6-7-8 18 mm spark plugs, 0.034 in. gap Hydraulic lifters 1958 Edsel Ranger, Pacer, Villager, Roundup, and Bermuda, standard equipment (called "E400") 4V 9.6:1 or 10.0:1 Compression Ratio depending on source of information. at 4600 rpm Torque at 2800 rpm × Bore/Stroke 4-bbl Ford (Autolite) carburetor Pushrod overhead valve Angle-wedge cast combustion chamber Firing order: 1-5-4-2-6-3-7-8 Cylinder numbering (front-to-rear): Right 1-2-3-4 Left 5-6-7-8 18 mm spark plugs, 0.034 in. gap Hydraulic lifters 1959 Edsel Corsair, Villager, and Ranger, optional equipment (called "Super Express V8")
360 Truck
The 361/360, of actual displacement, was introduced in 1968 and phased out at the end of the 1976-year run; it was used in the Ford F Series trucks and pickups. It has a bore of a 390 ( ) and used the 352's rotating assembly. The 361s and 360s were also constructed with heavy-duty internal components for truck use. Use of a standard 352/390 cam for use in passenger cars along with carburetor and distributor adjustment allowed the 360 to give performance similar to that of the 352 and 390 car engines. Rated at at 4100 rpm and of torque at 2600 rpm (two-barrel carb, 1968). The 360 used the same block, heads, and other parts as a 390, which makes them indistinguishable from each other unless the stroke is measured.
360 Truck engine configurations and applications
2V, 8.4:1 at 4100 rpm and at 2600 rpm 1968–1971 Trucks net at 4000 rpm and at 2400 rpm 1972–1976 Trucks
390
The 390 had a bore of , stroke of , and displacement of . It was the most common FE engine in later applications and was used in many Ford cars as the standard engine, including the Thunderbird, and in many trucks, as well. It was a popular high-performance engine; although not as powerful as the 427 and 428 models, it provided good performance, particularly in lighter-weight vehicles. The 2V is rated at at 4,100 rpm, while the 4V version was rated at at 4,100 rpm in certain applications. Certain 1967 and 1968 Mustangs had 390 4V engines rated at , as did some Fairlane GTs and S-code Mercury Cougars.
390 engine configurations and applications
2V 8.9:1 — at 4400 rpm and at 2400 rpm 1963–1965 Mercury 9.4:1 — at 4600 rpm and at 2400 rpm 1964–1965 Mercury 9.5:1 — at 4400 rpm and at 2600 rpm 1966 Ford 1966 Ford Fairlane 1966 Mercury 1966 Mercury Comet 9.5:1 — at 4400 rpm and at 2600 rpm 1967 Ford 1967–1968 Ford Fairlane 1967 Mercury 1967 Mercury Comet 1968 Ford Mustang 1968 Mercury Cyclone GT 1968 Mercury Cougar GT 10.5:1 — at 4600 rpm and at 2800 rpm 1968 Ford 1969 Mercury 9.5:1 — at 4400 rpm and at 2600 rpm 1968 Ford Fairlane 1968 Ford Torino 1968–1970 Ford 1968–1970 Mercury 8.6:1 — at 4400 rpm and at 2600 rpm 1968–1971 Trucks 9:1 — at 4400 rpm and at 2600 rpm 1971 Ford, Mercury 8.2:1 — net at 4000 rpm and at 2600 rpm 1972–1975 Trucks 4V 10.6:1 — at 6000 rpm and at 3400 rpm 1961–1962 Ford 9.6:1 — at 4600 rpm and at 2800 rpm 1961–1963 Ford 1961–1963 Ford Thunderbird 1963 Mercury 9.6:1 — at 5000 rpm and at 3200 rpm 1961–1963 Ford Police Interceptor 1963 Mercury Police Interceptor 10.1:1 — at 5000 rpm and at 3200 rpm 1964 Ford Police Interceptor 1964 Mercury Police Interceptor 11:1 — at 4600 rpm and at 2800 rpm 1964–1965 Ford 1964–1965 Mercury 1964–1965 Ford Thunderbird 10.5:1 — at 4600 rpm and at 2800 rpm 1966–1967 Ford 1966–1968 Ford Thunderbird 1968 Mercury 10.5:1 — at 4600 rpm and at 3200 rpm 1967, 1969 Ford Mustang 1967, 1969 Ford Fairlane 1967, 1969 Mercury Cyclone GT 1967, 1969 Mercury Cougar GT 1969 Ford Torino 1969 Mercury Montego 10.5:1 — at 4800 rpm and at 2800 rpm 3x2V, 10.6:1 at 6000 rpm and at 3500 rpm 1961–1962 Ford at 6000 rpm and at 3500 rpm 1962 Ford 1962–1963 Ford Thunderbird
Generation 2
406
The 406 engine was introduced in 1962 and only lasted to 1963, giving way to the 427. It used a new bore with the 390's stroke, giving a displacement of , rounded up to "406" for the official designation. The larger bore required a new block-casting design, allowing for thicker walls, but otherwise was very similar to the 390 block. Testing of the 406, with its higher power levels, led to cross-bolted mains - main bearing caps that were secured not only by bolts at each end coming up from beneath, but also by bolts coming in from the sides through the block. A custom-fit spacer was used between the cap and the block face. This design prevented the main bearing caps from "walking" under extreme racing conditions, and can be found today in many of the most powerful and modern engines from many manufacturers.
406 engine configurations and applications
4V, 11.4:1 — at 5800 rpm and at 3400 rpm 1962–1963 Ford 1963 Mercury 3x2V, 11.4:1 — at 5800 rpm and at 3500 rpm 1962 Ford 3x2V, 12.1:1 — at 5800 rpm and at 3500 rpm 1963 Ford, Mercury
410
The 410 engine, used in 1966 and 1967 Mercurys (see Ford MEL engine regarding 1958 senior series Edsels), used the same bore as the 390 engine, but with the 428's stroke, giving a real displacement. The standard 428 crankshaft was used, which meant that the 410, like the 428, used external balancing. A compression ratio of 10.5:1 was standard.
410 engine configurations and applications
4V, 10.5:1 — at 4600 rpm and at 2800 rpm 1966–1967 Mercury
427
s to pass through The 427 V8 was introduced in 1963 as a "top-oiler", changed to a side-oiler in 1965. Despite the "427" designation, its true displacement was . The stroke was the same as the 390 at , but the bore was increased to . The block was made of cast iron with a specially thickened deck to withstand higher compression. The cylinders were cast using cloverleaf molds; the corners were thicker all down the wall of each cylinder. Many 427s used a steel crankshaft, and all were balanced internally. Most 427s used solid valve lifters, with the exception of the 1968 block, which had oil passages drilled for hydraulic lifters. Higher-flow heads were available with matching "tunnel-port" intake manifolds, which routed pushrods through the intake's ports in brass tubes. As an engine designed for racing, it had many performance parts available both from the factory and the aftermarket. This engine was also used in the A/FX-cars like the famous Fairlane Thunderbolt. Two different 427 blocks were produced, the initial 1963 top oiler and starting in 1965 a side oiler. The top oiler delivered oil to the cam and valvetrain first and the crank second; the side oiler sent oil to the crank first and the cam and valvetrain second. This was similar to the oiling design from the earlier Y-block. The engine was available with low-rise, medium-rise, or high-rise manifolds, and either single or double four-barrel carburetors on an aluminum intake. Ford never released an official power rating. The side oiler-powered Ford GT40 MkIIs led to a 1-2-3 finish in the 1966 24 Hours of Le Mans, and the winner's podium in 1967.
427 engine configurations and applications
Low-riser intake, 4V 10.9:1 — at 5600 rpm and at 3200 rpm 1968 Mercury Cougar GT-E only (it was to be offered in the Ford Mustang, according to early press releases, but there are no records or verification of any factory 427 Mustangs). In the spring of 1968, the 428 Cobra Jet officially replaced the 427; however, leftover 427s were installed until late June of that year, when stocks were depleted. 11.6:1 — at 5600 rpm and at 3400 rpm 1963–1964 Ford 1963–1964 Mercury Low-riser intake, 2×4V 12:1 — at 6000 rpm and at 3700 rpm 1964 Ford Fairlane Thunderbolt, Mercury: High-riser intake, 2×4V 13.6:1 — at 7000 rpm and at 4700 rpm 1966–1967 Ford Fairlane 500 "R-Code", Mercury Mid-riser intake, 4V 11.0:1 — at 5600 rpm and at 3400 rpm 1965–1967 Ford 1965–1967 Mercury Mid-riser intake, two 4-barrel Holley 780 CFM carburetor 11.5:1 — at 6000 rpm and at 3700 rpm 1965–1967 Ford 1965–1967 Mercury 1965–1967 Shelby Cobra 427.
427 SOHC "Cammer"
The Ford single overhead cam (SOHC) 427 V8 engine, familiarly known as the "Cammer", was released in 1964 in an effort to maintain NASCAR dominance by seeking to counter the enormously large block Chrysler 426 Hemi "elephant" engine. The Ford 427 block was closer dimensionally to the smaller 392 CID first-generation Chrysler FirePower Hemi; the Ford FE's bore spacing was compared to the Chrysler 392's . The Ford FE's deck height of was lower than that of the Chrysler 392 at . For comparison, the 426 Hemi has a deck height of and bore spacing of ; both Chrysler hemis have decks more than taller than the FE. The engine was based on the high-performance 427 side-oiler block, providing race-proven durability. The block and associated parts were largely unchanged, but an idler shaft replaced the camshaft in the block, which necessitated plugging the remaining camshaft bearing oiling holes. The cast-iron heads were designed with hemispherical combustion chambers and a single overhead camshaft over each head, operating shaft-mounted roller rocker arms. The valvetrain consisted of valves larger than those on Ford wedge-head engines, made out of stainless steel and with sodium-filled exhaust valves to prevent the valve heads from burning, and dual valve springs. This design allowed for high volumetric efficiency at high engine speed. The idler shaft in the block in place of the camshaft was driven by the timing chain and drove the distributor and oil pump in conventional fashion. An additional sprocket on this shaft drove a second "serpentine" timing chain, long, which drove both overhead camshafts. The length of this chain made precision timing of the camshafts an issue at high revolutions. The engine also had a dual-point distributor with a transistorized ignition amplifier system, running 12 amperes of current through a high-output ignition coil. The engines were essentially hand-built for racing, with combustion chambers fully machined to reduce variability. Nevertheless, Ford recommended blueprinting before use in racing applications. With a single four-barrel carburetor, they weighed and were rated at at 7,000 rpm and of torque at 3,800 rpm, with dual four-barrel carburetors at 7,500 rpm and of torque at 4,200 rpm. Ford sold them via the parts counter, the single four-barrel model as part C6AE-6007-363S, and the dual carburetor model as part C6AE-6007-359J for $2350.00 (as of October, 1968). Ford's hopes to counter Chrysler were cut short, though. Enough 427 SOHCs were sold to have the design homologated, but Chrysler protests succeeded in getting NASCAR to effectively legislate the engine out of competition. This was due to the motor not being available in a factory-production motor vehicle. It was not the only engine ever banned from NASCAR; the 1963 Chevrolet 427 "mystery motor", the 1965 426 "Race Hemi", and the Chrysler A-925 DOHC Hemi were also banned during the 1960s for the same reason. Both the USAC and NASCAR announced their bans on using the SOHC engine in stock car events on 17 December 1965. The USAC commented, “We are simply following our rules which state the engine must be representative of volume production and readily available to the public. Eventually overhead cam engines probably will become part of the American production automobile and thus will meet the requirements. Until that time, however, it is our feeling that in announcing their overhead engine for stock car racing in 1966 the Ford Motor Co. has put the cart before the horse. At this time their proposed overhead cam engine is strictly a racing engine and as such does not meet the spirit of the rules.” Bill France, NASCAR president, permitted the engine at its drag races, but not at conventional “oval track” stock car circuits: "The single overhead cam engine at present is a race engine and does not fall into the stock car category. We look on it as an experimental engine and as such will evaluate it for the 1967 season.” Nevertheless, the SOHC 427 found its niche in non-stock drag racing, powering many altered-wheelbase A/FX Mustangs, and becoming the basis for a handful of supercharged Top Fuel dragsters, including those of Connie Kalitta, Pete Robinson, and Lou Baney (driven by Don "the Snake" Prudhomme). In 1967, Connie Kalitta's SOHC-powered "Bounty Hunter" slingshot dragster won Top Fuel honors at AHRA, NHRA, and NASCAR winter meets, becoming the only "triple crown" winner in drag racing history. It was also used in numerous nitrous-oxide funny cars, including those of Jack Chrisman, "Dyno" Don Nicholson, Eddie Schartman, and Kenz and Leslie, and in numerous gasoline-injected drag-racing vehicles.
428
For 1966, Ford combined attributes that had worked well in previous incarnations of the FE – a bore and a stroke – to create an easier-to-make engine. It used a cast nodular-iron crankshaft and external balancer. For 1966 this engine was offered as a 345 horsepower (257 Kilowatts) hydraulic Q-code 428 for standard production cars as well as a 360 horsepower (268 Kilowatts) solid-lifter P-code 428 Police Interceptor for law enforcement vehicles only. The solid-lifter 428 was available in 1966 only, replaced by a hydraulic version in 1967, also a P-code. The new-for-1966 Q-code 428 was also standard in FoMoCo's new full-size sport models which included the Galaxie 500 7-Litre and Mercury Monterey S-55. The 1966 Galaxie 500 7-Litre was the only example in Ford's history of a full-size model ever coming standard-equipped with an engine above 400 cubic inches in displacement. The Q-code 428 was also optional in all 1966 full-size Fords, Mercurys and the Ford Thunderbird which carried over into the 1967 model year. Same for 1968, the last year for Q-code production, except in the case of Thunderbirds which came standard with Ford's new N-code 429 engine. For 1969, full-size Fords & Mercurys began offering the N-code 429 in place of the 428. The 428 Police Interceptor continued production until the end of the 1970 model year.
428 engine configurations and applications
4V, 10.5:1 at 4600 rpm and at 2800 rpm 1966–1967 Q-code Ford 1966–1967 Q-code Ford Thunderbird 1966–1967 Q-code Mercury 1966 Q-code Ford Galaxie 500 7-Litre 1966 Q-code Mercury Monterey S-55 1967 Q-code Ford XL ordered with the "7-Litre Sports Package" 1967 Q-code Mercury Monterey ordered with the "S-55 Sports Package" at 5400 rpm and at 3200 rpm 1966 P-code solid lifter Ford & Mercury 428 Police Interceptor 1967–1970 P-code hydraulic lifter Ford & Mercury 428 Police Interceptor 1968 1/2 Shelby GT500KR Interceptor at 4600 rpm and at 2800 rpm 1968 Q-code Ford 1968 Q-code Mercury at 5400 rpm and at 3200 rpm 1968 Shelby GT500 2×4V, 10.5:1 – at 5400 rpm and at 3200 rpm 1967 Shelby GT500
428 Cobra Jet
(1969 Mustang) The 428 Cobra Jet was a performance version of the 428 FE. Launched in April 1968, it was built on a regular production line using a variety of cylinder heads combined with a 735 CFM Holley four-barrel carburetor. The Cobra Jet used heavier connecting rods with a 13/32 in rod bolt and a nodular iron crankshaft casting #1UB. A Holman and Moody specially prepared "stripper", which carried no sound deadener, undercoating, or any optional factory equipment, was used as the introductory press car in 1968. The 428 Cobra Jet had a compression ratio of 10.8:1 and was rated at 5200 rpm and at 3400 rpm. Historical road test data on actual production 428 CJ cars suggest peak output in the neighborhood of 275 SAE net ("as installed") HP, using published trap speed and "as tested" weights, and Hale's trap speed formula. Period road tests revealed quarter-mile performance in the low 14-second to very high 13-second range, with trap speeds around : The 428 Cobra Jet engine (modified to the NHRA Stock and Super Stock technical specifications) made its drag-racing debut at 1968 NHRA Winternationals, held February 2–4, 1968, at the Auto Club Raceway at Los Angeles County Fairgrounds, in Pomona, California. Ford Motor Company sponsored five drivers (Gas Ronda, Jerry Harvey, Hubert Platt, "Dyno" Don Nicholson, Kenneth McLellan, and Al Joniec) to race six 428 CJ-equipped Mustangs. They raced in classes C Stock Automatic (C/SA, ), based on advertised horsepower) and Super Stock E (SS/E or SS/EA, manual or automatic transmission, respectively, at , based on factored horsepower). The engine lived up to expectations, as four of the cars made it to their respective class finals. Al Joniec won both his class (defeating Hubert Platt in an all-CJ final) and the overall Super Stock Eliminator title (defeating Dave Wren, who red lighted in his faster 426 Race Hemi Plymouth).
428 Cobra-Jet engine configurations and applications
Cobra Jet — bore × stroke ; valvetrain: OHV two valves per cylinder, naturally aspirated four-barrel Holley carburetor, compression ratio: 10.6:1 rated at at 5200 rpm and maximum torque of at 3400 rpm 1968 Ford Mustang 1968 Mercury Cougar 1968 Shelby GT500KR 1968 Ford Fairlane 1968 Ford Torino 1968 Mercury Comet 1968 Mercury Cyclone 1969–1970 Ford Mustang 1969–1970 Mercury Cougar 1969 Ford Fairlane 1969 Ford Torino 1969 Ford Cobra 1969 Mercury Montego, Cyclone and CJ
428 Super Cobra Jet
The 428 Super Cobra Jet (also known as the 428 SCJ) used the same top end, pistons, cylinder heads, camshaft, valve train, induction system, exhaust manifolds, and engine block as the 428 Cobra Jet, but the crankshaft and connecting rods were strengthened and associated balancing altered for drag racing. A nodular-iron crankshaft casting #1UA was used, as well as heavier 427 "Le Mans" connecting rods with cap screws instead of bolts for greater durability. The heavier connecting rods and the removal of the center counterweight on the stock 428 Cobra Jet crankshaft (1UA) required an external weight on the snout of the crankshaft for balancing. A 428 Super Cobra Jet engine with oil cooler was standard equipment when the "Drag Pack" option (which came when selecting either a 3.91 or 4.30 rear end gear ratio) was ordered with cars manufactured from 13 November 1968. In addition, while the CJ and SCJ engines used the same autothermic piston casting, the piston-to-bore clearance specification between the CJ and SCJ 428 engines is slightly different, with the SCJ engines gaining a slightly looser fit to permit higher operating temperature. Horsepower measurements at a street RPM level remained the same. The 428 Super Cobra Jet engine was never offered with factory air conditioning due to the location of its engine oil cooler.
428 Super Cobra-Jet engine configurations and applications
Super Cobra-Jet — bore × stroke ; valvetrain: OHV two valves per cylinder, naturally aspirated four-barrel Holley carburetor, compression ratio: 10.6:1 rated at at 5200 rpm and maximum torque of at 3400 rpm 1969–1970 Ford Mustang 1969–1970 Mercury Cougar 1969 Ford Fairlane 1969 Ford Torino 1969 Ford Cobra 1969 Mercury Montego, Cyclone and CJ
Use
The FE series engines were used in cars, trucks, buses, and boats, as well as for industrial pumps and other equipment. Ford produced the engine from 1958 to 1976. Aftermarket support has continued, with replacement parts and many newly engineered and improved components. In Ford vehicles, the FE primarily powered full- and midsized cars and trucks, though it was also installed in both pony cars and midsized muscle cars, including in dedicated drag packages such as the 1964 Ford Fairlane Thunderbolt. Ford used the FE in podium-sweeping victories in its GT-40 at the 24 Hours of Le Mans, supported its use in factory associated high-performance Shelby Mustangs, and Shelby made the 427 CID version further famous in his Shelby Cobras.
Ford production vehicles
Some Ford production models in which the FE was installed: Ford Galaxie, Ford Custom 500, Ford Mustang, Ford Thunderbird - 3rd generation, Ford Thunderbird - 4th generation, Ford LTD, Ford Torino, Ford Ranchero, Ford Talladega, Ford Fairlane, and F-Series trucks though typically only those 1 ton and lesser in capacity. Ford regularly made updates to the design of the FE, which appear as engineering codes or variations in casting numbers of parts. In addition to production casting codes, Ford also made use of "SK" and "XE" numbers if the parts were one-offs or developmental designs not approved for production. Many parts attached to Ford's racing engines carried SK and XE numbers. Selection of vehicles in which the FE was installed as original equipment: File:1965 Ford Galaxie.jpg|1965 Ford Galaxie File:1960 Ford Galaxie Starliner.jpg|1960 Ford Galaxie Starliner File:1968 Ford Torino Squire.jpg|1968 Ford Torino Squire File:1965 Ford F100 Pick Up.jpg|1965 Ford F100 Pick Up File:1967 Ford Fairlane Ranchero.jpg|1967 Ford Fairlane Ranchero File:Red 1968 gtcs front.JPG|1968 GTCS File:FE vehicles Thunderbird1965.jpg|1965 Thunderbird File:'63 Ford Galaxie 500 Convertible (Rassemblement Saint-Bruno-De-Montarville '10).jpg|1963 Ford Galaxie 500 Convertible File:'59 Ford Galaxie (Auto classique Laval '10).jpg|1959 Ford Galaxie
Other uses
In addition to its use in Ford and Mercury branded vehicles, Ford itself, used it in factory, supported racing teams, and the FE was sold to third parties for use in their own products such as buses, and boats. Also, the FE was used to power irrigation pumps, generators and other machinery where long-running, low-rpm, reliable service was required.
In racing
FE s s as installed in competition 427 AC Cobras finished 1-2-3 in the 1966 24 Hours of Le Mans; this car finished 2nd Specific models that used FE engines include the AC Cobra MKIII, GT40s, the AC 428, as well as various factory racing versions of Ford Mustangs, Ford Galaxies, Ford Fairlanes, and Ford Thunderbirds. In the 1960s, most organized racing events required either stock components or components that were readily available to the general public. For NASCAR racing, rules required that at least 500 vehicles be sold to the general public equipped as raced. Many drag racing and road racing organizations had similar rules, which contributed to a wide range of performance parts being made available through Ford dealership parts counters. In addition, aftermarket suppliers produced performance parts and accessories. The use of the FE by Ford itself as the powerplant in many of its racing programs and performance vehicles resulted in constant improvements and engineering changes over the course of its life. Racing-inspired changes to the FE which later made it to production engines included the side-oiler block, which directed oil first to the lower portions of the block.
Custom automobiles
The FE engine is used extensively in custom installations. The extensive availability of multi-carburetor and other exotic intakes, as well as many other "dress-up parts", has contributed to its use where the engine would be shown off. FEs powered the original Batmobiles built by George Barris for the 1966 TV series. It fit under the hood along with the Bat-ray, Bat-ram, a nose-mounted aluminum chain slicer and all the associated support hardware of the 5,500-pound vehicle. One dragstrip version was equipped with a Holman-Moody prepped 427 FE with dual quads, which would be launched in second gear and spin its tires the entire quarter-mile length of the track. In 1968 Carroll Shelby created a custom Mustang using a California Special model and an experimental Ford 428 FE (known as a CJX, precursor to the 428 Cobra Jet). This "Green Hornet" had a custom independent rear suspension, four-wheel disc brakes and a Conelec electronically controlled port fuel injection system. It had a 5.7 sec 0-60 time and 157 mph top speed, versus a factory 428 cu in FE Shelby GT500's 6.5 second 0-60 and 128 mph top speed. File:Wiki Ed Roth pair of FEs.jpg|Pair of FEs used in an Ed Roth custom File:Batmobile from 2003 Car Exhibition.jpg|Batmobile File:Wiki 3 dual Paxtons on xram in Cobra.jpg|An FE with dual superchargers in a tribute to the 200 mph Cobra made famous by Bill Cosby File:2011 Ridler Award Winner with Ford SOHC.jpg|2011 Ridler Award winner – 1956 Ford Sunliner with an FE SOHC (Cammer)
Marine applications
The FE was popular in V-drive marine applications, available as a factory option in Century boats. Beginning in 1968, the U.S. Navy SEALS used twin 427 FEs to power their Light SEAL Support Craft (LSSC).
References
Further reading
External links
Text derived from https://en.wikipedia.org/w/index.php?oldid=1378755503 under CC BY-SA 4.0; modifications have been made.
References
- ↩Wikipedia “Ford FE engine” release date (×1) · confidence 0.95 revision URL