Giga Press

The Giga Press program is a series of aluminium die casting machines manufactured for Tesla, initially by Idra Group in Italy.

Uses your system voice; voice and rate in settings.

Snapshot

≈ 6 min read

Names in other languages

No names in other languages are held for this entry yet.

Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.

The Giga Press program is a series of aluminium die casting machines manufactured for Tesla, initially by Idra Group in Italy. Idra presses were the largest high-pressure die casting machines in production as of 2020, with a clamping force of . Each machine weighs .

Base specification Giga Press machines were included in Idra's catalogue in 2018. Tesla began using a custom Giga Press in late-2020 for integrated die-casting production of chassis parts for the Tesla Model Y. Shots of molten aluminium weighing are injected into the cold-chamber casting mold with a velocity of .

The cycle time is ~80–90 seconds, allowing an initial output rate of 40‒45 completed castings per hour, or ~1,000 castings per day.

Operation

Die casting works by forcing molten metal alloy inside a reusable mold, then opening the mold to remove the finished piece after it cools and solidifies. The opened mold is cooled to and cleaned by robots, and fresh molten aluminium is prepared for the next cycle to begin 1‒2 minutes after the first cycle.

Each fresh casting is trimmed to approximate size, measured, checked for imperfections, and sent for CNC machining to finished size. Ingots and off-cuts of aluminium are melted in a natural gas-powered melting oven operating at , until liquid.

Slag in the form of aluminium oxide is mechanically removed from the surface, and the rest of the liquid metal is pumped through heated pipes to an enclosed warming oven operating at , heated using of electrical power. To prevent the formation of oxides, a tank blanket of nitrogen gas covers the molten aluminium, which is circulated to maintain an even temperature.

Argon gas and a rotary-degasser are used to remove impurities, with a silicon carbide filter removing most other particles larger than . At the beginning of each casting cycle robots spray of soybean oil in a thin layer inside each half of the mold to allow separation. The mold is closed, and a low vacuum of created by pumping the air out.

A precise amount of molten metal is pumped from the holding oven into the casting chamber at , and forced into the mold using a high-speed plunger with an additional of lubricant. The mold is opened, and the raw casting removed at . A robot reaches in and removes the casting, placing it in a quenching tank to reduce the temperature from .

A mechanical trim press cuts the approximate edges, recycling excess aluminium into the melting oven. The remaining useful part of the casting is X-rayed to check its internal structure, trimmed by laser, drilled for fittings, and then computer-measured for precision.

Die structure

Tesla's Model Y rear casting dies have four known visible parts: two large classic main facing dies, oriented vertically with injection from the bottom of the immobile one. two smaller side wedging dies, moving in for injection and out for removal. The front casting suggests an identical die layout, with a possible fifth wedging die underneath (process) for the front-facing (car) crash rail mount.

Metal alloy

Sandy Munro analysed a Model Y casting in 2021 and reported that the casting aluminium alloy used in the large Tesla chassis parts is primarily an aluminium 89.5%‒silicon 8.5% mix, plus several other trace elements, falling within the categorisation of aluminium Association alloy "AA 386":

Components

Vacuum inside the closed mold is achieved using a 4,000-litre tank made by Fondarex in Switzerland. Molten metal is pumped through heated pipes, and rotary degassing is performed to reduce porosity.

Steps and machinery involved: StrikoMelter Melting and Holding Furnace ( ) Holding oven (~ ) Giga Press ("DCM"‒Die-casting machine) Quench oil tank Mechanical trim press X-Ray machine (porosity check) Plasma arc trimming. Drill and tap (machining) Laser scanning (coordinate-measuring machine, ) Fastener insertion Scrap metal shredder (immediate closed loop recycling of aluminium offcuts) Vacuum system

Tesla

In 2019 Jerome Guillen indicated that Tesla Automation were working on a "giant, giant, giant machine" to "make full-size cars in the same way that toy cars are made". In April 2020, Tesla CEO Elon Musk said that Tesla had purchased the two biggest casting machines in the world to cast the Tesla Model Y rear chassis and crash rails.

In January 2021, Musk stated that the rear chassis of the Tesla Cybertruck would be produced using a casting machine larger than . As of October 2021, Tesla had five casting machines installed at Giga Shanghai, two machines installed at Tesla Factory in Fremont, two machines installed at Giga Berlin, and two machines going into Giga Texas—plus foundations in preparation for many additional Giga Press machines.

During May/June 2022, Idra were assembling a Giga Press. , two 9,000 ton presses were available at GigaTexas to cast Cybertruck rears, while Cybertruck front castings are cast on a 6500-ton press that is shared for casting Model Y frames. Total GigaPresses at Texas were two 9,000 ton plus four of the smaller presses.

Germany

plans for Giga Berlin included eight die casting machines. (Located at .) European Model Y cars have front and rear cast chassis sections. The first two European Giga Press machines were planned to be delivered to Giga Berlin by the start of 2021.

Shanghai

(July 2020) By October 2020, three locally made LK Machinery Impress-Plus DCC6000 machines were undergoing assembly for Model Y production. (Located at .) As of October 2021, five machines were available.

Texas

in January 2021 For Tesla Model Y car production at Giga Texas beginning in 2022, Tesla began to deploy a single-piece front in addition to the existing single-piece rear casting. During the night of 18/19 January 2021, concrete foundations for three Giga Press machines were poured at the Giga Texas factory location near Austin, Texas.

( ) On 21 January 2021 the first Giga Press components started to arrive on site. , all major components of the first Giga Press at the Austin site had been craned into place. On 15 April 2021, components for a second Giga Press started arriving at Giga Texas.

Glovitech

LK Technology delivered one Impress-Plus DCC 6000 machine for Glovitech of South Korea, installed in the Vân Trung Industrial Zone, Việt Yên, Bắc Giang Province, Vietnam. The machine is used for producing large Faraday cages (radio-frequency enclosures) for 5G mobile base stations. The machine was delivered in December 2020, and produced its first castings in March 2021.

Volvo

By November 2023, orders had been placed for two 9000-tonnes-force Giga Press machines for a new Volvo electric vehicle factory at Košice, Slovakia.

Text derived from https://en.wikipedia.org/w/index.php?oldid=1360401063 under CC BY-SA 4.0; modifications have been made.

Sources cited in this revision

31 named source(s) extracted from the cited revision. A source with no author is shown by its publication; nothing is invented.