Programmer (hardware)
≈ 4 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
socket alt=BPM 3928 Automated Programming System|thumb|The 3928, with up to seven sites, is made for programming large data devices, such as MCUs, eMMC HS400, NAND, NOR and Serial Flash devices. High-speed signals support devices up to 200 MHz and the latest eMMC HS400 modes with data transfer rates of 2.5 nanoseconds per byte. In the context of installing firmware onto a device, a programmer, device programmer, chip programmer, device burner, or PROM writer is a device that writes, a.k.a. burns, firmware to a target device's non-volatile memory. Typically, the target programmable chip is one of the following types: PROM, EPROM, EEPROM, Flash memory, eMMC, MRAM, FeRAM, NVRAM, PLD, PLA, PAL, GAL, CPLD, FPGA, microcontroller.
socket]] In the context of installing firmware onto a device, a programmer, device programmer, chip programmer, device burner, or PROM writer is a device that writes, a.k.a. burns, firmware to a target device's non-volatile memory. Typically, the target programmable chip is one of the following types: PROM, EPROM, EEPROM, Flash memory, eMMC, MRAM, FeRAM, NVRAM, PLD, PLA, PAL, GAL, CPLD, FPGA, microcontroller.
Connection
Connector-based On-Board Programmer for AVR microcontroller with USB Port interface]] Generally, a programmer connects to a device in one of two ways.
Insertion
In some cases, the target device is inserted into a socket (usually ZIF) on the programmer. If the device is not a standard DIP packaging, a plug-in adapter board, which converts the footprint with another socket, is used.
Cable & port
In some cases, a programmer connects to a device via a cable to a connection port on the device. This is sometimes called on-board programming, in-circuit programming, or in-system programming.
Transfer
Data is transferred from the programmer to the device as signals via connecting pins. Some devices have a serial interface for receiving data (including JTAG interface). Other devices communicate on parallel pins, followed by a programming pulse with a higher voltage for programming the data into the device. Usually, a programmer is controlled via a connected personal computer through a parallel port, USB port, or LAN interface. A program on the controlling computer interacts with the programmer to perform operations such as configure install parameters and program the device,
Types
There are four general types of programmers: Automated programmers often have multiple programming sites/sockets for mass production. Sometimes used with robotic pick and place handlers with on-board sites to support high volume and complex output such as laser marking, 3D inspection, tape input/output, etc. Development programmers usually have a single programming site; used for first article development and small-series production. Pocket programmers for development and field service. Specialized programmers for certain circuit types only, such as FPGA, microcontroller, and EEPROM programmers.
Manufacturers
For each vendor's web site, refer to "External links" section. Batronix GmbH & Co. KG BPM Microsystems Conitec Datasystems Data I/O Corporation DediProg Technology Co., Ltd Elnec s.r.o Elprosys Sp. z o.o. halec Hi-Lo System Research MCUmall Electronics Inc. Phyton, Inc. Xeltek Inc.
See also
Off-line programming In-system programming Debug port JTAG interface Common Flash Memory Interface Open NAND Flash Interface Working Group Atmel AVR#Programming interfaces PIC microcontroller#Device programmers Intel HEX – ASCII file format SREC – ASCII file format ELF – Binary file format COFF – Binary file format Hardware description language
References
External links
Technical information JEDEC - Memory Configurations: JESD21-C JEDEC - Common Flash Interface (CFI) Specification, JESD68.01, September 2003. Intel - Common Flash Interface (CFI) and Command Sets IEEE Std 1532-2002 (Revision of IEEE Std 1532-2001) - IEEE Standard for In-System Configuration of Programmable Devices What is the IEEE 1532 Standard? Keysight Technologies JEDEC - STANDARD DATA TRANSFER FORMAT BETWEEN DATA PREPARATION SYSTEM AND PROGRAMMABLE LOGIC DEVICE PROGRAMMER: JESD3-C, Jun 1994 JEDEC - JC-42 Solid State Memories Manufacturers Batronix GmbH & Co. KG BPM Microsystems Conitec Datasystems Inc. Data I/O Corporation Elnec s.r.o. Elprosys Sp. z o.o. Dediprog halec Hi-Lo System Research Co. Ltd. MCUmall Electronics Inc. Minato Holdings Inc. Phyton, Inc. Xeltek Inc.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1358895751 under CC BY-SA 4.0; modifications have been made.