Specific detectivity
Specific detectivity, or D*, for a photodetector is a figure of merit used to characterize performance, equal to the reciprocal of noise-equivalent power (NEP), normalized per square root of the sensor's area and frequency bandwidth…
≈ 5 min read
Names in other languages
No names in other languages are held for this entry yet.
Article bodies are English and are not machine-translated. A name in another language is not a translation of the article.
Specific detectivity, or D*, for a photodetector is a figure of merit used to characterize performance, equal to the reciprocal of noise-equivalent power (NEP), normalized per square root of the sensor's area and frequency bandwidth (reciprocal of twice the integration time).
Specific detectivity is given by D∗=ANEP, where A is the area of the photosensitive region of the detector, and NEP the noise equivalent power (in units of W/Hz)[1]. It is commonly expressed in Jones units (cm⋅Hz/W) in honor of Robert Clark Jones who originally defined it.[2][3]
Given that noise-equivalent power can be expressed as a function of the responsivity ℜ (in units of A/W or V/W) and the noise spectral density Sn (in units of A/Hz1/2 or V/Hz1/2) as NEP=Snℜ, it is common to see the specific detectivity expressed as D∗=ℜ⋅ASn.
It is often useful to express the specific detectivity in terms of relative noise levels present in the device. A common expression is given below.
- D∗=qληhc[4kTR0A+2q2ηΦb]−1/2
With q as the electronic charge, λ is the wavelength of interest, h is the Planck constant, c is the speed of light, k is the Boltzmann constant, T is the temperature of the detector, R0A is the zero-bias dynamic resistance area product (often measured experimentally, but also expressible in noise level assumptions), η is the quantum efficiency of the device, and Φb is the total flux of the source (often a blackbody) in photons/s/cm2.
Detectivity measurement
edit edit sourceDetectivity can be measured from a suitable optical setup using known parameters. You will need a known light source with known irradiance at a given standoff distance. The incoming light source will be chopped at a certain frequency, and then each wavelength will be integrated over a given time constant over a given number of frames.
In detail, we compute the detection bandwidth Δf directly from the integration time constant tc.
- Δf=12tc
Next, an average signal and rms noise needs to be measured from a set of N frames. This is done either directly by the instrument, or done as post-processing.
- Signalavg=1N(∑iNSignali)
- Noiserms=1N∑iN(Signali−Signalavg)2
with the NEP=NoisermsΔf. Now, the computation of the radiance H in W/sr/cm2 must be computed where cm2 is the emitting area. Next, emitting area must be converted into a projected area and the solid angle; this product is often called the etendue. This step can be obviated by the use of a calibrated source, where the exact number of photons/s/cm2 is known at the detector. If this is unknown, it can be estimated using the black-body radiation equation, detector active area Ad and the etendue. This ultimately converts the outgoing radiance of the black body in W/sr/cm2 of emitting area into one of W observed on the detector.
The broad-band responsivity, is then just the signal weighted by this wattage.
- R=SignalavgHG=Signalavg∫dHdAddΩBB,
where
- R is the responsivity in units of Signal / W, (or sometimes V/W or A/W),
- H is the outgoing radiance from the black body (or light source) in W/sr/cm2 of emitting area,
- G is the total integrated etendue between the emitting source and detector surface,
- Ad is the detector area,
- ΩBB is the solid angle of the source projected along the line connecting it to the detector surface.
From this metric noise-equivalent power can be computed by taking the noise level over the responsivity.
- NEP=NoisermsRΔf=NoisermsSignalavgHGΔf
Similarly, noise-equivalent irradiance can be computed using the responsivity in units of photons/s/W instead of in units of the signal. Now, the detectivity is simply the noise-equivalent power normalized to the bandwidth and detector area.
- D∗=AdNEP=ΔfAdHGSignalavgNoiserms
See also
edit edit sourceReferences
edit edit source- ^ Rogalski, A. (2012-01-01). "History of infrared detectors". Opto-Electronics Review. 20 (3). doi:10.2478/s11772-012-0037-7. ISSN 1896-3757. Wikipedia revision 1372315522, retrieved 2026-11-19
- ^ R. C. Jones, "Quantum efficiency of photoconductors," Proc. IRIS 2, 9 (1957) Wikipedia revision 1372315522, retrieved 2026-11-19
- ^ R. C. Jones, "Proposal of the detectivity D** for detectors limited by radiation noise," J. Opt. Soc. Am. 50, 1058 (1960), doi:10.1364/JOSA.50.001058) Wikipedia revision 1372315522, retrieved 2026-11-19
This article incorporates public domain material from Federal Standard 1037C. General Services Administration. Archived from the original on 2022-01-22.
Text derived from https://en.wikipedia.org/w/index.php?oldid=1372315522 under CC BY-SA 4.0; modifications have been made.